Results 21 to 30 of about 66,945 (308)
Microstructural and XRD analysis and study of the properties of the system Ti-TiAl-B4C processed under different operational conditions [PDF]
, 2018 High specific modulus materials are considered excellent for the aerospace industry. The system Ti-TiAl-B4C is presented herein as an alternative material. Secondary phases formed in situ during fabrication vary depending on the processing conditions and
Arévalo Mora, Cristina María +4 more
core +2 more sources
Fabricating Graphene-Titanium (
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2019 Titanium has themost useful properties of the metal are corrosion resistancestrength-to-density ratio, the highest of any metallic element. In itsunalloyed condition, titanium is as strong as some steels but less dense.
Tuğba Mutuk, Mevlüt Gürbüz
doaj +1 more source
An Initial Assessment of Infiltration Material Selection for Selective Laser Sintered Preforms [PDF]
, 2004 High-temperature infiltration is an important process that is used to add strength to skeletal microstructures. In this study, particulate metal matrix composites (MMCs) are fabricated.
Barrow, Stacia L. +2 more
core +1 more source
Investigating the influence of fine-dispersed aluminum, nickel and titanium on the properties of phenylone [PDF]
, 2019 Розглянуто вплив металевих наповнювачів на фізико-механічні та трибологічні характеристики ароматичного поліаміду фенілон – багатообіцяючий термостійкий полімер конструкційного призначення, який може довго експлуатуватися до температури 533 К та не ...
Burya, Aleksandr +5 more
core +1 more source
Wear Behavior of Self-mated Ti-Si-C Composites and Ti-Si-N Composites Slid Without Lubricant
Tribology Online, 2008 To develop lightweight wear-resistant titanium matrix composites, the wear behaviors of three kinds of composites produced from SiC and titanium (Ti-Si-C composite) and three kinds of composites produced from Si3N4, TiN and titanium (Ti-Si-N composite ...
Yuko Hibi, Takashi Murakami
doaj +1 more source
Reactive sintering of B4c-TiB2 composites from B4 and TiO2 precursors [PDF]
Processing and Application of Ceramics, 2020 The effect of sintering temperature in the interval from 1775 to 1850°C on the density, microstructure, hardness and fracture toughness of ceramic composites consisting of a boron carbide matrix and titanium diboride secondary phase was studied.
Švec Pavol +2 more
doaj +1 more source
Dry sliding wear behavior of TiB/Ti and TiC/Ti composites
Mechanical Engineering Journal, 2018 Titanium and its alloys have excellent strength properties and corrosion resistance, but they show poor wear resistance, which cannot be improved by heat treatment.
Hiroshi IZUI +3 more
doaj +1 more source
Materials & Design, 2020 Crack-free and almost fully dense (≥99%) bulk-form titanium matrix nanocomposites in-situ synthesized from a ball-milled mixture of Ti-6Al-4V and B4C powders were achieved through an optimized selective laser melting (SLM) process.
Hailiang Li +4 more
doaj +1 more source
Crystals, 2022 One of the popular techniques to fabricate metal matrix composites is the compo-casting process. The un-uniform spreading of reinforced subdivisions (particles) inside the metallic matrix and the lack of desirable mechanical properties of the final ...
Weining Wang +2 more
doaj +1 more source
Advances in Materials Science and Engineering, 2023 The current study examines the effect of titanium carbide reinforcement (TiC) on the tribological behavior of copper metal matrix composites. The stir-casting process followed by hot rolling was employed to fabricate the composite parts.
S. Harish +3 more
doaj +1 more source