Results 81 to 90 of about 1,895,111 (298)
Mesh-based tool path calculations for tubular joints
Advances in Mechanical Engineering, 2020 Manufacturing of large steel tube structures is faced with excessive welding, fit-up and rework times in tube joints, due to various types of deviation from nominal shape of the tubes.
Morten Lind, Pål Ystgaard
doaj +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Tool path generation of ultra-precision diamond turning: A state-of-the-art review
Nanotechnology and Precision Engineering, 2019 With the increasing market demand for optical complex surface parts, the application of multi-axis ultra-precision single-point diamond turning is increasing. A tool path generation method is very important to decrease manufacturing time, enhance surface
Hu Gong +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Thread cutting with 3-axis N/C milling machine [PDF]
, 1968 TAPDIE, a generalized macro written for the APT numerical control system, cuts threads in stock too big for conventional machines or for which conventional methods are unsuitable.
Salley, G. C., Wood, C. H., Jr.
core +1 more source
, 2019 This paper presents a language-independent proof system for reachability properties of programs written in non-deterministic (e.g., concurrent) languages, referred to as all-path reachability logic. It derives partial-correctness properties with all-path
Ciobaca, Stefan +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
A smooth tool path generation and real-time interpolation algorithm based on B-spline curves
Advances in Mechanical Engineering, 2018 In the machining progress of free-form surface, tool path is presented as continuous small line segments. To achieve high machining speed and fine machining quality, the tool path needs to be smoothed.
Shujie Sun +3 more
doaj +1 more source