Results 91 to 100 of about 99,684 (313)
MetalsHot isostatic pressing (HIP) is a near-net shape powder metallurgy (PM) technique, which has emerged as an efficient technique, offering precise control over the microstructure and properties of materials, particularly in high-performance alloys.
Faezeh Javadzadeh Kalahroudi +3 more
doaj +1 more source
Dimethyl Fumarate, But Not Rituximab, Reduces Serum GFAP Levels and PIRMA in Relapsing–Remitting MS
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objective Serum neurofilament light chain (sNfL) and glial fibrillary acidic protein (sGFAP) levels are believed to reflect mainly acute and chronic disease processes in multiple sclerosis (MS), respectively. In this study, we investigated whether dimethyl fumarate (DMF) and rituximab (RTX) differentially affect these biomarkers.
F. Shawket +14 more
wiley +1 more source
DEVELOPMENT AND RESEARCH OF THE NEW STEEL 75‘/25ГМФС FOR THE INSTRUMENT OF COLD FORMING
Литьë и металлургия, 2015 The problems of improving tool life of cold deformation. Composition designed and studied mechanical properties of the new tool steel 75H5GMFS, by allowing the application of different types of heat treatment, including high-temperature tempering after ...
V. M. Fedulov
doaj
Metals, 2018 Any improvement on the service life of tools reduces the tooling costs, and assists to increase labor productivity by decreasing the needs for either the tools’ re-grinding or their replacement.
Peter Jurči +3 more
doaj +1 more source
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Traumatic spinal cord injury (TSCI) caused by sharp‐force penetration is exceptionally rare, and the use of high‐dose methylprednisolone (MP) remains highly controversial, especially beyond the conventional 8‐h treatment window. This case report describes a 30‐year‐old male with acute incomplete TSCI following a knife stab wound to the right ...
Honghong Wang +5 more
wiley +1 more source
, 2016 The microstructure and properties of a 5 wt.% Cr cold work tool steel were studied after austenitisation at 1020°C, 1050°C or 1075°C followed by single, double and triple tempering treatments at 525°C.
Rehan, Arbab +3 more
core
Micromilling of hardened (62 HRC) AISI D2 cold work tool steel [PDF]
, 2012 Investigations into micro-slot milling of high carbon, high chromium hardened AISI D2 cold work tool steel using 0.5mm diameter coated (TiAlN) tungsten carbide end mills were carried out.
Saedon, Juri Bin
core
, 2010 To produce clean commercial tool steel the non-metallic inclusions characteristics have to be known, since they influence the mechanical properties of steel. In this work, inclusion characteristics in steel samples from plant trials were studied.
P.G. Jönsson +5 more
core +1 more source
INFLUENCE OF QUANTITATIVE ALLOYING OF TOOL STEELS FOR HOT DEFORMATION ON THE LEVEL OF HARDENING
Литьë и металлургия, 2015 The influence of complexly experimental tool steels: C (0,4–0,50%), Si (0,6–1,2%), Mn (0,17–0,8%), Cr (0,8–3%), W (0,9– 4%), Mo (0,01–3.5%) and V (0,28–1,8%) on their ability to hardening due to only high-temperature tempering after induction melting ...
V. N. Fedulov
doaj
Properties Evaluation of Thin Microhardened Surface Layer of Tool Steel after Wire EDM
Metals, 2016 This paper describes results of experimental research on the thin microhardened surface layer of a machined surface that occurs in materials using wire electrical discharge machining (WEDM) with brass wire electrode. The direct influence of microhardened
Ľuboslav Straka +2 more
doaj +1 more source