Results 131 to 140 of about 99,684 (313)

General Reference and Design S-N Curves Obtained for 1.2709 Tool Steel. [PDF]

Materials (Basel), 2023
Böhm M, Niesłony A, Derda S, Owsiński R, Kepka M, Zetkova I, Zetek M, Houdková Š, Prażmowski M.   +8 more
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Change of Inclusion Characteristics during Vacuum Degassing of Tool Steel

, 2006
The inclusion characteristics were studied during vacuum degassing by interrupting the operation at five different times after the start of operation.
Steneholm, Karin,, Margareta Andersson, Pär Jönsson, Jönsson, Pär,, Andersson, Margareta A.T.,, Karin Steneholm   +5 more
core   +1 more source

Optimization of Grinding Parameters of Tool Steel by the Soft Computing Technique. [PDF]

Comput Intell Neurosci, 2022
Hatami O, Sayadi D, Razbin M, Adibi H.
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Quenching and partitioning - a new steel heat treatment concept [PDF]

, 2011
Steel continues to be one of the primary materials in use today, however, even after 200 years of published research, innovative methods are being discovered and exploited to produce steel with enhanced properties.
Bigg, Timothy David
core  

Processing of a Martensitic Tool Steel by Wire-Arc Additive Manufacturing. [PDF]

Materials (Basel), 2022
Ziesing U, Lentz J, Röttger A, Theisen W, Weber S.   +4 more
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

A Newly Designed High-Strength Tool Steel with High Wear and Corrosion Resistance. [PDF]

Materials (Basel), 2023
Zeisig J, Shtefan V, Giebeler L, Kühn U, Gebert A, Hufenbach JK.   +5 more
europepmc   +1 more source

What Do Large Language Models Know About Materials?

Advanced Engineering Materials, EarlyView.
If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer, Thomas Wallmersperger, Gianaurelio Cuniberti   +2 more
wiley   +1 more source