Results 71 to 80 of about 154,688 (325)
Proximal versus Distal Screw Placement for Biceps Tenodesis: A Biomechanical Study
Journal of Orthopaedic Surgery, 2016 Purpose To assess the maximum and end torque of a fourth-generation composite humerus model with no screw inserted or with a screw inserted in the distal (subpectoral) position or proximal (suprapectoral) position.
Daniel Johannes De Villiers +3 more
doaj +1 more source
Effects of spin current on ferromagnets
, 2005 When a spin-polarized current flows through a ferromagnet, the local magnetization receives a spin torque. Two consequences of this spin torque are studied.
J. He, Malozemoff A. P., S. Zhang, Z. Li
core +1 more source
Establishing the Relative Merits of Interior and Spoke-Type Permanent-Magnet Machines With Ferrite or NdFeB Through Systematic Design Optimization [PDF]
, 2015 In this paper, a multiobjective design optimization method combining design-of-experiments techniques and differential-evolution algorithms is presented.
Demerdash, Nabeel +3 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Effect of operating conditions on gearbox noise [PDF]
, 1992 Low contact ratio spur gears were tested in the NASA gear noise rig to study the noise radiated from the top of the gearbox. The measured sound power from the gearbox top was obtained from a near field acoustic intensity scan taken at 63 nodes just above
Atherton, William +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
On Planar Five-bar Motion Generation with a Driver Torque Constraint
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2008 In motion generation, the objective is to calculate the mechanism parameters required to achieve or approximate a set of prescribed rigid-body positions.
Qiong SHEN +3 more
doaj +1 more source
Improved spectral stability in spin transfer nano-oscillators: single vortex versus coupled vortices dynamics [PDF]
, 2015 We perform a comparative study of spin transfer induced excitation of the gyrotropic motion of a vortex core with either uniform or vortex spin polarizers. The microwave output voltage associated with the vortex dynamics, detected in both cases, displays
Cros, Vincent +7 more
core +3 more sources
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source