Results 191 to 200 of about 21,720 (312)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

A fault diagnosis method for inter-turn short circuit based on magnetic field distribution. [PDF]

Sci Rep
Wang B, Wang L.
europepmc   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Analyzing and reducing common mode noise in high power inductive power transfer systems for electric vehicles using precise balance technique. [PDF]

Sci Rep
Mei Y, Weng W, Wu J, Xu H, He X, Wang Y.
europepmc   +1 more source

Enhanced Gamma Radiation Shielding Using Epoxy Quartz Fabric Composites Reinforced With CoCl2 Microparticles

Advanced Engineering Materials, EarlyView.
The growing demand for lightweight, nontoxic, and multifunctional gamma shielding materials has intensified efforts to find alternatives to conventional lead and aluminum‐based protectants. In this work, we develop epoxy quartz fabric composites reinforced with cobalt chloride (CoCl2) microparticles, fabricated via hand lay‐up with varying filler ...
Summan Urooge, Ahsan Irshad, Umar Jamil, Srosh Fazil, Khuram Liaqat, Kashif Shahzad, Fakhar Alam, Mehboob Alam   +7 more
wiley   +1 more source

Condition monitoring and fault diagnosis of power transformer based on non-invasive measurement. [PDF]

Sci Rep
Youssef M, El-Said Abdelaziz, Mohamed HS, Attia M.   +3 more
europepmc   +1 more source

Laser Metal Powder Deposition of Titanium Microalloyed HSLA Steel FeC0.12Si0.25Mn1.3

Advanced Engineering Materials, EarlyView.
This study investigates the additive manufacturing of titanium‐doped high‐strength low‐alloy (HSLA) steel via laser metal deposition. It reveals distinct process‐structure relationships for elemental powder blends compared to prealloyed feedstocks.
Olaf Stelling, Matthias Steinbacher, Nils Ellendt   +2 more
wiley   +1 more source

High Voltage Flyback Converter for Safety Indicators in Electrical Testing Laboratories. [PDF]

Sensors (Basel)
Drăgoi AD, Lica S, Lie I, Popescu MV.
europepmc   +1 more source

Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review

Advanced Engineering Materials, EarlyView.
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente, J. Nunes‐Pereira, A. P. Silva, P. N. B. Reis   +3 more
wiley   +1 more source

Digital protection scheme based on Durbin Watson and Pearson similarity indices for current signals practically applied to power transformers. [PDF]

Sci Rep
Mahmoud RA.
europepmc   +1 more source