Results 131 to 140 of about 3,770,661 (245)

Tribological behaviour of ZA27/10SiC/1Gr hybrid composite

, 2013
The paper describes the tribological behaviour of a hybrid composite based on zincaluminium ZA27 alloy, reinforced with siliconcarbide (SiC) and graphite (Gr) particles. The composite specimen was prepared by compocasting technique.
Miloradović, Nenad, Stojanovic, Blaza
core  

Optimizing the Tribological Behavior of Nanocrystalline Inconel 718 by Solid Lubricant Reinforcements. [PDF]

Tribol Lett
Kasalo M, Nayak UP, MacLucas T, Suarez S, Bachmaier A.   +4 more
europepmc   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, Volume 28, Issue 18, 23 September 2026.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

Taguchi optimization of tribological properties of Al/SiC/graphite composite

, 2016
Investigation of tribological behaviour of the hybrid composite, whose substrate is Al/Si alloy A356, reinforced with 10 wt. (%) of silicon carbide (SiC) and 0 and 5 wt. (%) of graphite (Gr) is presented in this paper by application of the Taguchi method.
Ivanović, Lozica, Babic, Miroslav, Stojanovic, Blaza   +2 more
core  

Tribological Behavior and Attachment Force Regulation of Bioinspired Claw-Spines. [PDF]

Biomimetics (Basel)
Zhang Y, Wu X, Wu H, Wu X, Zhang F, Jia B, Li X, Pang J.   +7 more
europepmc   +1 more source

Tribological Behavior of Soybean Oil

, 2019
Constantin Georgescu, Lorena Deleanu, George Catalin Cristea   +2 more
openaire   +2 more sources

Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites

Polymer Composites, Volume 47, Issue 18, Page 16212-16232, 20 September 2026.
Schematic illustration of the experimental procedure of the specimens. ABSTRACT This research work investigated the effect of the cyclic thermo‐hygrometric aging regime between −20°C and +40°C with 0–400 cycles on the reciprocating tribological properties of fused deposition modeling (FDM) printed polylactic acid (PLA) and the same material reinforced ...
Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yılmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy   +5 more
wiley   +1 more source

Tribological aspects of contemporary gear materials

, 2010
The aim of this paper is to determine the problems of selecting gear materials due to tribological aspects as meta-analysis. Gear performance is profoundly influenced by tribology.
Ivanović, Lozica, Ilic, Andreja, Josifović, Danica   +2 more
core  

Comparative Study of Microstructure, Phase Composition, Hardness, and Tribological Behavior of Low-Carbon Steel After Electrolytic-Plasma and Laser Surface Hardening. [PDF]

Materials (Basel)
Sulyubayeva L, Buitkenov D, Maulit A, Alibekova B, Bolatov S.   +4 more
europepmc   +1 more source

Investigation of the Mechanical and Tribological Behavior of Epoxy-Based Hybrid Composite. [PDF]

Polymers (Basel), 2023
Albahkali T, Fouly A, Alnaser IA, Elsheniti MB, Rezk A, Abdo HS.   +5 more
europepmc   +1 more source