Results 41 to 50 of about 3,442 (165)
ISIJ International, 2001 The influence of heat-treating conditions on the retention of carbon-enriched austenite of TRIP-assisted multiphase steel grades containing different amounts of silicon and/or aluminium is investigated. The ensuing mechanical properties resulting from the TRIP effect are also scrutinised.
Jacques, P. J. +3 more
openaire +2 more sources
Advance in Research on Evolution of Structure in TRIP Steels during TMP and Heat Treatment
Teshugang, 2007 Influence factors on evolution of structure in hot rolled TRIP steels during TMP(Thermnomechanical processing)finishing rolling(austenite deformed in non-crystallization region),ROT(run out table)cooling(phase transformation in y-a two phase region)and ...
唐代明
doaj
Rheological Behavior of TRIP600 Steel during Deformation
MetalsDue to the phenomenon of deformation-induced phase transformation, the mechanical properties of TRIP steel, including the elastic modulus, undergo changes during the deformation process.
Yanjun Yin, Hengyan Zhai, Xinfeng Kan
doaj +1 more source
THERMO-MECHANICAL TREATMENT OF 42SICR AND 42MNSI STEELS
Acta Metallurgica Slovaca, 2017 Two high strength low alloyed steels with 0.4%C, 0.6%Mn, 2%Si and either 1.3% of chromium or without chromium were used in this work to evaluate the effect of chromium on the final microstructure obtained by thermo-mechanical processing.
Ludmila Kučerová +2 more
doaj +1 more source
Materials & Design, 2019 This study developed a powder feeding laser metal deposition (LMD) method that can be used to achieve a layer-by-layer fabrication of component grade material for efficiently screening the properties of different chemical compositions and determining the
Kuan Zhang +7 more
doaj +1 more source
Effect of Annealing Temperature on Structure of 0.2C-1.5Si-1.5Mn-(0.5Cu)TRIP Steel
Teshugang, 2005 The effect of annealing temperature between 750 ℃ and 780 ℃ on structure of two TRIP steel - 0.2C-1.5Si- 1.5Mn and 0.2C-1.5Si-1.5Mn-0.5Cu has been studied by color metallograph method, X-ray diffraction and scanning electron micrograph.
景财年 +5 more
doaj
Evaluation of Shear-Punched Surface Layer Damage in Three Types of High-Strength TRIP-Aided Steel
MetalsThe damage properties in the shear-punched surface layer, such as the strain-hardening increment, strain-induced martensite fraction, and initiated micro-crack/void characteristics at the shear and break sections, were experimentally evaluated to relate ...
Koh-ichi Sugimoto +2 more
doaj +1 more source
Effects of Ar and He on Microstructures and Properties of Laser Welded 800MPa TRIP Steel
MATEC Web of Conferences, 2018 Fiber laser welding of cold rolled TRIP steel (transformation Induced Plasticity steel) sheet with tensile strength of 820MPa and thickness of 1.4mm was carried out using shielding gases Ar and He, respectively. For the same laser power and welding speed,
Wang Wen-Quan +3 more
doaj +2 more sources
Change of ears creation of AHSS steels after heat treatment of zinc coating
Metalurgija, 2014 The article deals with the normal anisotropy, the earring evaluation of deep-drawing steels DC06, micro-alloyed steel H220 and steel with transformation induced plasticity TRIP RAK 40/70 and deals with the influence of annealing temperature to ears ...
E. Spišák, J. Majerníková, J. Slota
doaj
Materials & DesignMechanical properties of thick steel plates used in shipbuilding, construction, and marine structures are critical, particularly under low-temperature and high-impact conditions.
Junha Yang, Sukjin Lee
doaj +1 more source