Results 21 to 30 of about 1,375 (177)
PARAMETRIC ANALYSIS OF WELDING PARAMETERS ON TIG (TUNGSTEN INERT GAS) WELDING DISSIMILAR MATERIALS
International Journal of Research and Analytical Reviews, 2022 The use of TIG Welding to combine dissimilar materials is a new area for weight reduction in power generation, electric, nuclear, petrochemical and chemical industries. A successful weld between dissimilar material is one that is as strong as the weaker of the two metals being joined, i.e., possessing sufficient tensile strength and ductility so that ...
Jaksan D. Patel +3 more
openaire +1 more source
MATEC Web of Conferences, 2018 The paper concerns the issue of the impact of welding defects on the strength of EN AW 5754 aluminium alloy welded joints, executed with the TIG welding method (tungsten inert gas, i.e., a method of welding with a non-consumable tungsten electrode ...
Woźny Piotr, Błachnio Józef
doaj +1 more source
Crystals, 2023 316L stainless steel joined to mild steel is widespread in several applications to reach a requested good association of mechanical properties at a lower cost.
Kamel Touileb +5 more
doaj +1 more source
Parametric Study and Optimization for Welding Processes Using Machine Learning
Annals of "Dunarea de Jos" University of Galati, Fascicle XII, Welding Equipment and Technology, 2021 Optimization facilitates in attainment of maximum strength, efficiency, reliability, productivity and longevity. In this work, data from three material joining processes - Ultrasonic welding of polymers, arc welding as Metal Inert Gas and Tungsten Inert ...
M. Chaturvedi, S. Arungalai Vendan
doaj +1 more source
Influence of oxide content in activated tungsten inert gas welding
Zavarivanje i zavarene konstrukcije, 2022 In this paper, welding-remelting of AISI 304L (X2CrNi19-11) austenitic stainless steel was performed by using TIG process with activating flux, that is, A-TIG process. Fluxes were prepared by mixing 5, 10, 20, 30 and 40 % SiO2 nano particles with acetone solvent, while the application of the flux was done by a brush, prior to electric arc engagement ...
Sebastian Baloš +6 more
openaire +1 more source
Research on Arc Length Tracking Control Technology of Tube-Sheet Welding Based on Pulsed TIG
IEEE Access, 2023 During tungsten inert gas welding process, arc length will change due to thermal deformation, uneven surface of workpiece and tungsten electrode loss. Considering the large fluctuation of arc length in all-position annular seam welding under the action ...
Jianhua Ma +4 more
doaj +1 more source
Investigation of fatigue strength and norms of emission of harmful substances in the air during MIG and TIG welding of 1460 aluminium-lithium alloy [PDF]
FME Transactions, 2019 This work presents the results of studying harmful substances in the air, released in the case of tungsten inert gas (TIG) and metal inert gas (MIG) welding of 1460 aluminum alloy (Al-Cu-Li).
Lukianenko Anna +4 more
doaj
Forces in Mechanics, 2022 Many applications in industry require a material-to-material joining process of Duplex Stainless Steels (DSS). Therefore, it is essential to investigate the material's properties during a welding process to control the weld quality.
Lukas Quackatz +2 more
doaj +1 more source
Cycling Performance of Sodium‐Metal Chloride Battery Cells and Modules Based on Iron and Zinc
Advanced Energy Materials, EarlyView.High‐utilization sodium–metal chloride cells with a mixed‐metal Fe, Zn, NaCl cathode enable efficient high‐temperature cycling (300°C) while reducing cost and environmental impact. Near‐theoretical capacity and high efficiency are achieved in single cells.
William Nash +10 more
wiley +1 more source
Development of an Artificial Intelligence-Based System for Predicting Weld Bead Geometry
Applied Sciences, 2023 The prediction of the weld bead geometry parameters is an important aspect of welding processes due to it is related to the strength of the welded joint.
Ngoc-Hien Tran +2 more
doaj +1 more source