Results 121 to 130 of about 231,961 (313)

Automated Process Optimization in a Novel Triple Shaft Mixer with Adaptive Mixing Modes

Chemie Ingenieur Technik, EarlyView.
A novel multi‐purpose mixer with adjustable blade angle and a coaxial stirrer is developed, providing three degrees of freedom. An optimization strategy is integrated to autonomously identify optimal operating conditions through automated tests. The current draw of the main stirrer serves as the optimization criterion, while stirrer speeds, directions,
B. Schwarz, H. Kniele, J. A. Lindner
wiley   +1 more source

Review for "Performance enhancement of the artificial neural network–based reinforcement learning for wind turbine yaw control"

, 2019

openalex   +1 more source

Simulation of Impinging Cooling Performance with Pin Fins and Mist Cooling Adopted in a Simplified Gas Turbine Transition Piece [PDF]

, 2014
Tao Xu, Hang Xiu, J. Li, Haichao Ge, Qing Shao, Guang Yang, Zhenglei Yu   +6 more
openalex   +1 more source

Multi-Objective Optimization and Optimal Airfoil Blade Selection for a Small Horizontal-Axis Wind Turbine (HAWT) for Application in Regions with Various Wind Potential [PDF]

, 2022
Vahid Akbari, Mohammad Naghashzadegan, R. Kouhikamali, Farhad Afsharpanah, Wahiba Yaïci   +4 more
openalex   +1 more source

Potential Analysis of On‐Site Oxygen and Ozone Production for Wastewater Treatment Plants

Chemie Ingenieur Technik, EarlyView.
The potential of a power‐to‐gas process focusing on the oxygen stream to cover an upcoming demand of ozone at German wastewater treatment plants is analyzed. Economic and ecological parameters are compared to the conventional production of hydrogen and oxygen. Powered by on‐site produced wind energy, the process is deemed beneficial.
Vincenta Franßen, Paul Goerdten, Christian Hoffmann, Jens‐Uwe Repke   +3 more
wiley   +1 more source

Optimisation of the spray parameters for improved microstructural characteristics in the HVOF sprayed Cr3C2-20(Ni20Cr) coating

Journal of Materials Science: Materials in Engineering
Wear resistance coating of Cr3C2-20(Ni20Cr) is required to be sprayed through High Velocity Oxy Fuel (HVOF) Spray Process on the compressor disc of aero gas turbine engine. The part is made up of Ti6Al4V alloy.
Hariharan Venkataraman, Vishal Uttamrao Bagade, V. M. Biju, S. S. K. Balam, M. Tamilselvi   +4 more
doaj   +1 more source

Durene conversion in a methanol‐to‐jet process: Exploring conversion at 150–350°C over different acid catalysts

The Canadian Journal of Chemical Engineering, EarlyView.
Abstract Acid catalyzed conversion of durene by isomerization, disproportionation, and transalkylation is of interest to the development of a methanol‐to‐jet process to reduce the amount of durene in the kerosene. It was of interest to determine whether durene conversion could be performed at a temperature lower than 350°C.
Aida G. Velasco Ortiz, Risha Raju, Arno de Klerk   +2 more
wiley   +1 more source

Fault Diagnosis of Wind Turbine Bearings Based on CEEMDAN-GWO-KELM [PDF]

, 2022
Liping Liu, Ying Wei, Xiu‐Yun Song, Lei Zhang   +3 more
openalex   +1 more source

Production of middle distillates through olefin oligomerization using ZSM‐5 as a catalyst

The Canadian Journal of Chemical Engineering, EarlyView.
Abstract The global transportation sector relies heavily on gasoline (C5–C12) and diesel (C11–C24), which together account for approximately 60% of its energy needs. Driven by rapid industrialization and urbanization, diesel consumption is outpacing gasoline, with projections estimating global demand by 2035 at 27 million barrels per day for gasoline ...
Thembekile Hoyi, Masikana Milan Mdleleni, Ntalane Sello Seroka, Lindiwe Khotseng   +3 more
wiley   +1 more source

Dynamic response of an offshore wind turbine subject to ice loading in glacial tills [PDF]

Pengxu Zou, Jeremy D. Bricker, Ayumi Fujisaki‐Manome   +2 more
openalex   +1 more source