Results 41 to 50 of about 1,241 (293)
High-Speed and Low-Load Twin-Roll Casting of Al–5%Mg Strip
Metals, 2022 A conventional twin-roll caster usually casts strips at a speed slower than 2 m/min and a roll load greater than 2 kN/mm. A vertical-type high-speed twin-roll caster can cast aluminum alloy strips at a speed higher than 10 m/min and a roll load smaller ...
Kazuki Yamazaki, Toshio Haga
doaj +1 more source
Frontiers in Metals and AlloysIn this study the influence of varying twin-roll casting (TRC) conditions on the microstructure, texture and mechanical properties of a Mg-6.8Y-2.5Zn-0.4Zr alloy (WZ73) was investigated. In particular the twin-roll cast speed and rolling gap were varied.
Franziska Ueberschär +2 more
doaj +1 more source
Technological Provision of Quality of Shafs of Twin-Roll Casting Rolls
, 2021 С. Абрамов: ORCID 0000-0003-0675-4850UKR: Мета. Забезпечення якості валів валків-кристалізаторів за рахунок поліпшення охолодження на машинобудівному підприємстві. Методика.
Абрамов, Сергій Олексійович +3 more
core +1 more source
Study of the Mechanical Properties of Strips Obtained in TRC Line
Archives of Metallurgy and Materials, 2016 Twin Roll Casting technology belongs to modern, integrated method of processing aluminum and its alloys. This method includes preparation of liquid metal and its continuous casting between the rotating cylindrical crystallizers, optional homogenizing ...
Mamala A. +4 more
doaj +1 more source
Twin Roll Casting of Aluminium Alloy ADC12, A3003, A7075
, 2017 This paper describes a vertical type twin roll strip casting process for producing aluminum alloy strip of ADC12, A3003 and A7075. Twin roll casting process is able to produce a strip from molten metal directly.
Junshi Ichikawa +8 more
core +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Relieving segregation in twin-roll cast Mg–8Al–2Sn–1Zn alloys via controlled rolling
Journal of Magnesium and Alloys, 2021 Twin-roll casting (TRC) of Mg alloys with high Al content has unique advantages and broad development prospects. However, the severe segregation of high-alloyed Mg caused by TRC technology is difficult to solve at present, which restricts its practical ...
Shao-You Zhang +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Casting Process at Roll Bite in Strip Cast Using Vertical-Type High-Speed Twin-Roll Caster
Metals, 2022 The solidification process in strip casting using a vertical-type high-speed twin-roll caster was clarified by inserting a 0.1 mm diameter K-type thermocouple into a strip during casting.
Toshio Haga, Yukihiro Kurahashi
doaj +1 more source
Asymmetric Twin-Roll Casting of an Al-Mg-Si-Alloy
, 2018 The industrial application of high-alloyed Al-Mg-Si alloys for the production of thin strips by means of twin-roll casting is limited due to the structural inhomogeneity and segregation formation.
Maria Bauer +3 more
core +1 more source