Results 101 to 110 of about 37,166 (237)
Improving impact resistance of ceramic materials by energy absorbing surface layers [PDF]
Energy absorbing surface layers were used to improve the impact resistance of silicon nitride and silicon carbide ceramics. Low elastic modulus materials were used.
Kirchner, H. P., Seretsky, J.
core +1 more source
Review of Electrochemical Methods for Battery Recycling
Chemie Ingenieur Technik, EarlyView.Electrochemical methods for the recycling of batteries are reviewed and different approaches for enhanced leaching, separation, and recovery methods are compared regarding their efficiency and suitability for potential application. ABSTRACT Research on innovative methods for the recycling of battery waste materials using electrochemical procedures is ...
Christian Modrzynski
wiley +1 more source
Megawatt Class Nuclear Space Power Systems (MCNSPS) conceptual design and evaluation report. Volume 1: Objectives, summary results and introduction [PDF]
The objective was to determine which reactor, conversion, and radiator technologies would best fulfill future Megawatt Class Nuclear Space Power System Requirements.
Wetch, J. R.
core +1 more source
Revisiting the synthesis of dimethyl carbonate from methanol and carbon dioxide
The Canadian Journal of Chemical Engineering, EarlyView.Abstract The process for producing dimethyl carbonate (DMC) from carbon dioxide (CO2) and methanol is explored in this article. It provides an overview of the thermodynamics involved in DMC synthesis, discussing the challenges and potential solutions. The article highlights the reported use of catalysts and dehydrating agents to improve DMC yield and ...
Diego Alexander Santos Araque +3 more
wiley +1 more source
Transmission electron microscopy characterization of microstructural features of Al-Li-Cu alloys [PDF]
A transmission electron microscopy (TEM) examination of aluminum-lithium-copper alloys was conducted. The principal purpose is to characterize the nature, size, and distribution of stringer particles which result from the powder metallurgy (P/M ...
Avalos-Borja, M. +2 more
core +1 more source
ChemSusChem, Volume 18, Issue 6, March 15, 2025.A sustainable alternative to steam cracking, the molten‐salt‐mediated oxidative dehydrogenation (MM‐ODH) of ethane (C2H6) in Li2CO3‐Na2CO3‐K2CO3 (LNK) couples thermal cracking with melt‐mediated CO2 capture to realize commercially competitive C2H4 and CO yields. LNK composition strongly influences MM‐ODH process outcomes.
Kyle Vogt‐Lowell +6 more
wiley +1 more source
ChemSusChem, Volume 18, Issue 6, March 15, 2025.Lithium carbonate (Li2CO3) obtained from the black mass of recycled lithium batteries is dissolved in water under controlled conditions to remove lithium fluoride (LiF), which is present at a concentration of 3.08 % by weight. The dissolution is carried out at temperatures below 10 °C, and it has been demonstrated that lower temperatures result in ...
Laura Rosso +3 more
wiley +1 more source
Corrosion of niobium-1 percent zirconium alloy and yttria by lithium at high flow velocities [PDF]
Lithium corrosion of niobium zirconium alloys and yttrium oxides at high flow ...
Hays, L. G.
core +1 more source
ENERGY &ENVIRONMENTAL MATERIALS, EarlyView.Cu‐doped spinel MnCo1.5Cu0.5O4 exhibits excellent conductivity and stability as SOC contact material. After 1000‐h aging at 850 °C, the contact layer maintains a 10 mΩ cm2 ASR value, and a single‐cell stack achieves a H2O/CO2 co‐electrolysis power density of 0.52 W cm−2.
Haozhen Li +7 more
wiley +1 more source
ENERGY &ENVIRONMENTAL MATERIALS, EarlyView.This article explores high‐entropy‐stabilized oxides (HEOs) as novel functional materials for addressing critical issues in lithium–sulfur (Li–S) batteries, including lithium polysulfide (LPS) shuttling, inadequate conductivity, and slow redox kinetics.
Hassan Raza +10 more
wiley +1 more source