Results 41 to 50 of about 144,621 (340)

2095) Flexural Ultimate Strength of Reinforced Concrete Section : Ultimate Condition of Beams with Tensile Reinforcement

Transactions of the Architectural Institute of Japan Summaries of Technical Papers, 1966
Hsien-teh You
openalex   +3 more sources

Investigation of the Tensile Properties of High-Strength Bolted Joints in Static Drill Rooted Nodular Piles

Applied Sciences
To address the persistence of traditional welded joints in the construction of static drill rooted nodular piles, high-strength bolted connections are introduced.
Zhongjin Wang, Qinyong Du, Rihong Zhang, Xinyu Xie   +3 more
doaj   +1 more source

Assessment of Foolad Mobarakeh ST14 Low Carbon Steel Sheet for Automobile Frames [PDF]

International Journal of Advanced Design and Manufacturing Technology, 2007
In this research formability behavior and texture of St14 low carbon steels produced by Foolad Mobarakeh plant for deep drawing application had been studied. Plate textures were characterized by X-ray Diffraction technique.
Ehsan Mohamadi, Mehdi Taheri, Amir Zomorodian   +2 more
doaj  

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

The Effects of Cupping Therapy on Biomechanical Properties in Wistar Rat Skin

مجله پژوهش در علوم توانبخشی, 2013
Introduction: In most Asian countries, cupping therapy has been used as a therapeutic method for soft tissue lesions but there is no high quality evidence-based support for its clinical efficacy. Cupping therapy may have an influence on the biomechanical
Traneh Norozali, Mohammad Mohsen Roostayi, Farideh Dehghan Manshadi, Mehdi Abbasi, Alireza Akbarzadeh Baghban, Mohammad Reza Khaleghi   +5 more
doaj   +1 more source

Laser Metal Deposited Ti4822 Hollow Pipe: Experimental and Computational Modelling Study

Advanced Engineering Materials, EarlyView.
Laser metal deposition (LMD) of a crack‐free built Ti4822 alloys is challenging. This article reports outstanding characteristics of a hollow pipe that is built with LMD technology when a predicted, nontransformation substrate temperature of 800 °C is used.
Sadiq A. Raji, Monnamme Tlotleng, Samuel Skhosane, Lehlogonolo R. Kanyane, Abimbola P. I. Popoola, Sisa L. Pityana   +5 more
wiley   +1 more source

Numerical Analysis of Shear-off Failure of Keyed Epoxied Joints in Precast Concrete Segmental Bridges [PDF]

, 2016
Precast concrete segmental box girder bridges (PCSBs) are becoming increasingly popular in modern bridge construction. The joints in PCSBs are of critical importance, which largely affects the overall structural behavior of PCSBs. The current practice is
Shamass, R, Shamass, R, Wu, Z, Wu, Z, Zhou, X, Zhou, X   +5 more
core   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Optimization for Friction Welding Input Factors to Maximize Tensile Strength and Minimize Axial Shortening in ASTM A516 Grade 70 steel Rods

Journal of Applied Science and Engineering, 2022
The Intention of this work is to state a design of process parameters in the continuous drive friction welding of ASTM A516 Grade 70 steel, 12 mm diameter and 100 mm length circular rods by using central composite design (CCD) in response surface ...
G. Senthilkumar, T. Mayavan, R. Ramakrishnan   +2 more
doaj   +1 more source

Cryogenic container compound suspension strap [PDF]

, 1980
A support strap for use in a cryogenic storage vessel for supporting the inner shell from the outer shell with a minimum heat leak is presented. The compound suspension strap is made from a unidirectional fiberglass epoxy composite material with an ...
Vorreiter, J. W.
core   +1 more source