Results 111 to 120 of about 54,093 (284)
Advanced Materials, EarlyView.A general, versatile laser‐shock synthesis process is reported to produce various bimetallic CuNi, CuFe, CuCo, and medium‐entropy CuFeCoNi heterostructures, in which crystalline metal nanoparticles are anchored to amorphous hydroxide supports. During nitrate reduction reaction, the heterostructures undergo dynamic amorphous/crystalline reconstruction ...
Weihua Guo +18 more
wiley +1 more source
Advanced Materials, EarlyView.A soft–hard tri‐layer composite electrolyte that couples fast Li+ transport with reinforced interfacial stability to enable high‐conductivity, mechanically robust, dendrite‐free lithium‐metal batteries. ABSTRACT The development of solid polymer electrolytes is central to safe, high‐energy lithium‐metal batteries (LMBs); however, persistent challenges ...
Fazal Ur Rehman +9 more
wiley +1 more source
Optical parametric oscillators : a comparison of new materials
, 2015 A study of new materials for optical parametric oscillators (OPOs) was carried out using an XeCI excimer laser as a pump source. The three non-linear optical materials studied were lithium borate (LBO), deuterated L-arginine phosphate (d-LAP) and β ...
Robertson, Gordon
core
Virtual Inertia Control for Damping Low-Frequency Oscillation in IBR-Dominated Networks
Increased reliance on renewables brings challenges to maintaining the electric networks' inertia and damping and poses concerns about network stabilization.
Pradana, A +4 more
core +1 more source
Damping of low frequency pressure oscillation [PDF]
, 2007 A hydraulic line between a hydraulic pump and an actuator comes under much stress when a pulsatile actuator is used. It causes a huge pressure oscillation in the hydraulic system and thus decreases reliability.
Ijas, M.
core
Synchronization of Low-Frequency Oscillation in Power Systems
, 2017 This paper presents the well-documented concept of synchronization of low frequency oscillation occurring in power systems and describes the characteristics of sync occurring in basic electrical circuits.
Seon-Ju Ahn +2 more
core +1 more source
Advanced Materials Interfaces, EarlyView.Schematic illustration of a sustainable nanofabrication process: chitosan derived from natural sources is used as a biodegradable thin film resist, patterned via Constant Pulse‐Assisted Force Lithography (CP‐AFL) to create tunable nanogrooves. These grooves template gold nanowire formation, enabling high‐resolution nanopatterning under ambient ...
Paolo Pellegrino +7 more
wiley +1 more source
, 2019 Anfeng Xiang,1,* Yang Yu,2,* Xize Jia,3,4 Huibin Ma,5,6 Hui Liu,1 Yu Zhang,1 Jun Rong,7,* Sheng Liu1,* 1School of Acupuncture-Moxibustion and Tuina, Shanghai University of Traditional Chinese Medicine, Shanghai, China; 2Department of Psychiatry, the ...
Liu H +7 more
core
Advanced Materials Interfaces, EarlyView.Ultrathin MXene/EMF composite foams achieve a specific shielding efficiency of 749.6 dB.dB·cm3$\mathrm{dB}\cdot {\mathrm{cm}}^{3}$/g, while the silver‐enhanced MXene/Ag/EMF reaches 81.4 dB shielding effectiveness at just 1.0 mm thickness. Both composites exhibit rapid Joule heating, retain stability up to 250∘C$^\circ{\rm C}$, and withstand 1000 ...
Abdullah A. Mahmood +7 more
wiley +1 more source
Minimally Invasive Delivery of Optical Nanosensors Using Injectable Hydrogels
Advanced Materials Interfaces, EarlyView.Injectable peptide hydrogels offer a minimally invasive delivery platform for single‐walled carbon nanotube (SWCNT)‐based near‐infrared fluorescent sensors, enabling real‐time measurement of drug concentrations. Encapsulated SWCNTs show a dose‐dependent fluorescence response across physiologically relevant concentrations and retain their fluorescence ...
Shirel Kleiner, Gili Bisker
wiley +1 more source