Results 91 to 100 of about 11,409,916 (219)

UCST‐Responsive PMEGA: From Solution Behavior to Functional Hydrogel Surfaces

Advanced Materials Interfaces, EarlyView.
PMEGA is used as a versatile water‐based UCST‐responsive platform for engineering microstructured hydrogel coatings via a thiol–ene CLAG approach. From PMEGAs of well‐defined UCST properties, the UV‐based CLAG method provides precise control over film thickness, ranging from nanometers to micrometers, and enables high‐resolution patterning.
Thi Phuong Thu Nguyen, Léa Milenkovic, Bruno Bresson, Nadège Pantoustier, Yvette Tran   +4 more
wiley   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

3D‐Printed Corneal Substitutes: Materials, Fabrication, and Preclinical Progress

Advanced Materials Technologies, EarlyView.
Successful clinical translation of 3D‐printed corneal substitutes relies on the interplay between the bioink properties, cellular component, and the fabrication process. These factors influence the critical properties of the construct, including optical transparency, mechanical stability, suture retention, that ultimately govern long‐term stromal ...
Shadi Moshayedi, Ashley Vazquez, Alexander J. Choi, Dimitrios Karamichos, Jayoung Kim   +4 more
wiley   +1 more source

Advanced Manufacturing of Composite‐Based Systems for Energy Applications

Advanced Materials Technologies, EarlyView.
Advanced manufacturing enables the integration of polymers, ceramics, metal oxides, and composites into architected microstructures with tailored transport pathways. By coupling material selection, manufacturing strategy, and structural design, multifunctional energy systems can simultaneously improve electrochemical performance, thermal management ...
Sri Vaishnavi Thummalapalli, Dhanush Patil, Libin Yang, M. Taylor Sobczak, Anshul Kulkarni, Xiao Sun, Arunachalam Ramanathan, Tiantian Li, Ramaraja P. Ramasamy, Jason J. Locklin, Yanyu Chen, Xianqiao Wang, Arunachala Mada Kannan, Kenan Song   +13 more
wiley   +1 more source

Quantum Dots at Ultra-Low temperatures

, 2005
NRC publication ...
Sachrajda, Andrew
core  

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

A Cryopreservation‐Based Supply Chain Strategy for Extrusion Bioprinting in Space

Advanced Materials Technologies, EarlyView.
Extrusion bioprinting on crewed space platforms requires a bioink that stays functional along the logistic chain. Here, cells and biomaterial ink travel separately, the cells cryopreserved and the ink cold stored, and are combined only minutes before printing.
Johannes Windisch, Max von Witzleben, Richard Frank Richter, Finn Dani, Constantin Greil, Sarah Duin, Anja Lode, Michael Gelinsky   +7 more
wiley   +1 more source

Wavelength‐Multiplexed 2D Beam Steering via a Passive Diffractive Network

Advanced Optical Materials, EarlyView.
Illustration of a wavelength‐multiplexed diffractive beam steering system, which is composed of K cascaded diffractive layers, each containing phase‐modulating elements that are jointly optimized using deep learning–based optimization. When illuminated with a set of wavelengths {λ1,λ2,…,λNw}$\{ {{{\lambda }_1},{{\lambda }_2},\ldots ,{{\lambda }_{{{N}_w}
Che‐Yung Shen, Yuhang Li, Çağatay Işıl, Tianyi Gan, Mona Jarrahi, Aydogan Ozcan   +5 more
wiley   +1 more source

Projeto de um circuito divisor de frequência de ultra-baixo consumo de potência [PDF]

, 2013
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-graduação em Engenharia ElétricaEsta dissertação apresenta o projeto de um circuito Prescaler Dual-Modulus 8/9 (PDM), projetado para a tecnologia TSMC 0 ...
Giusti, Gustavo Buchweitz
core  

3D Printing of Soft Robotic Systems: Advances in Fabrication Strategies and Future Trends

Advanced Robotics Research, EarlyView.
Collectively, this review systematically examines 3D‐printed soft robotics, encompassing material selections, function integration, and manufacturing methodologies. Meanwhile, fabrication strategies are analyzed in order of increasing complexity, highlighting persistent challenges with proposed solutions.
Changjiang Liu, Bin Cui, Xumin Huang, Xiaoyu (Rayne) Zheng, T. Thang Vo‐Doan, Ruirui Qiao   +5 more
wiley   +1 more source