Results 101 to 110 of about 63,195 (336)
Ultrasonic distance sensor improvement using a two-level neural network [PDF]
, 1995 This paper discusses the performance improvement that a neural network can provide to a contactless distance sensor based on the measurement of the time of flight (TOF) of an ultrasonic (US) pulse.
Ferraris, Franco +13 more
core +1 more source
Enhancing Bubble Removal in Geometry‐Optimized Electrodes
Advanced Engineering Materials, EarlyView.3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner +5 more
wiley +1 more source
, 2019 “C” scan ultrasonic scan testing has not been widely used in the inspection of materials compared to other ultrasonic testing procedures such as “A” scan even though the “C” scan has a higher productivity as it is automated.
Loke, Zhen Dong
core
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Design of high frequency ultrasonic array transducers for medical imaging
, 2011 Ultrasonic transducers have been widely used in the medical applications. High frequency array transducers have recently attracted many research interests, since it provides not only the electronic beamforming but also the very fine image resolution. The
Qian, Yichen
core
Frequency response of underwater ultrasonic transducers in the near field using polarimetric polarization maintaining fiber sensors [PDF]
, 2010 Near-field ultrasonic response (50-2000 kHz) of an underwater 1-3 piezocomposite transducer is experimentally investigated using a polarimetric polarization maintaining fiber sensor.
Hayward, Gordon +14 more
core +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
Inverse Kinematic Analysis and Evaluation of a Robot for Nondestructive Testing Application
Journal of Robotics, 2015 The robot system has been utilized in the nondestructive testing field in recent years. However, only a few studies have focused on the application of ultrasonic testing for complex work pieces with the robot system. The inverse kinematics problem of the
Zongxing Lu +4 more
doaj +1 more source
Biomass Native Structure Into Functional Carbon‐Based Catalysts for Fenton‐Like Reactions
Advanced Functional Materials, EarlyView.This study indicates that eight biomasses with 2D flaky and 1D acicular structures influence surface O types, morphology, defects, N doping, sp2 C, and Co nanoparticles loading in three series of carbon, N‐doped carbon, and cobalt/graphitic carbon. This work identifies how these structural factors impact catalytic pathways, enhancing selective electron
Wenjie Tian +7 more
wiley +1 more source
Correlation-based Scan Matching using Ultrasonic Sensors for EKF Localization
, 2018 This paper presents a localization method for a mobile robot equipped with only low-cost ultrasonic sensors. Correlation-based Hough scan matching was used to obtain the robot's pose without any predefined geometric features.
Chung, WK, Minyoung Choi, Jinwoo Choi
core +1 more source