Results 41 to 50 of about 52,181 (311)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Fatigue deformation of 1050 aluminum in ultrasonic fatigue testing.

Journal of Japan Institute of Light Metals, 1995
Ultrasonic fatigue tests have been performed on commercial 1050 aluminum. Internal friction (Q-1) has been measured during fatigue tests and as a function of strain amplitude (e). It is shown that more than 109 cycles test is necessary in order to determine the fatigue limit. Q-1 versus e curves have the inflection points at particular strain amplitude
Atsushi YAMAMOTO, Morihiko MAEDA, Harushige TSUBAKINO, Takuichi IMANAKA, Jun SUETSUGU   +4 more
openaire   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Study on ultrasonic evaluation of connection state and service performance of resistance projection welding joints

Discover Applied Sciences
Fatigue failure of welded joints is a performance factor of structural parts under dynamic load, and the effective evaluation of its life is always the key to the service ability of structures.
Zhenzhen Duan, Xueshan Zhao, Guanghao Zhou, Kunning Jia, Xiaopeng Gu, Ting Ma   +5 more
doaj   +1 more source

Fatigue lifetime of AlBC(3) alloy by ultrasonic fatigue testing machine in cavitation regime

The Journal of Engineering, 2015
In this study, the influence of ultrasonic nanocrystalline surface modification (UNSM) technique on the cavitation fatigue properties of AlBC(3) alloy was investigated.
I.S. Cho, A. Amanov, I.G. Park
doaj   +1 more source

ULTRASONIC ATTENUATION IN STEELS DURING FATIGUE [PDF]

Le Journal de Physique Colloques, 1985
The change of ultrasonic attenuation Ɗα as a function of fatigue cycle number n correlates well with the length of fatigue crack. A depinning model of dislocations with kinks is suggested to interpret the experimental results.
Zhengliang, Pan, Guangyi, Li
openaire   +1 more source

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

Scaling Invariance of Fatigue Crack Growth in Gigacycle Loading Regime [PDF]

, 2010
The role of the collective behavior of defect ensembles at the crack tip and the laws of fatigue crack propagation in R4 high strength steel have been studied under conditions of symmetric tension–compression gigacycle loading at 20 kHz.
BANNIKOV, M.V., NAIMARK, O.B, OBORIN, V., PALIN-LUC, Thierry   +3 more
core   +5 more sources

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source