Results 21 to 30 of about 1,044 (205)
Journal of Materials Research and Technology, 2022 High strength S960 steel was processed by shot peening and ultrasonic spray method to fabricate a surface hardened layer with a lubricant graphene oxide(GO) coating, and the wear test was performed to evaluate the tribological behavior after the ...
Zheng Yang +4 more
doaj +1 more source
A comparative review of effect of ultrasonic shot peening on LCF behavior of the alloys [PDF]
, 2022 The low cycle fatigue (LCF) behaviour of AA7075, AA2014, and austenitic stainless steel was studied in relation to ultrasonic shot peening (USSP) treatment, with all three materials sharing nearly identical parameters for ultrasonic shot peening ...
Mohamad Rusydi, Mohamad Yasin +1 more
core +1 more source
Microstructure, thermal stability and corrosion behavior of ultrasonic shot peened AA7034
Corrosion Communications, 2023 Microstructure, thermal stability at room temperature and corrosion behavior of ultrasonic shot peened AA7034 were investigated in this work. Microstructure modification induced by ultrasonic shot peening was obtained by using OM, SEM, EBSD and XRD, and ...
Hao Liu +5 more
doaj +1 more source
Shot peening of ceramics: Damage or benefit?
, 2022 S.185-190Non-transformation toughened ceramics show the typical brittle material behavior of failure before deformation at room temperature. Thus, strengthening of ceramics due to deformation induced compressive residual stresses has been thought to be ...
Frey, T., Pfeiffer, W.
core +1 more source
Modelling of multiple impacts for the prediction of distortions and residual stresses induced by ultrasonic shot peening (USP) [PDF]
, 2012 During a manufacturing process, the ultrasonic shot peening (USP) technique can be used as the final surface treatment. The aim of this operation is to introduce surface compressive residual stresses in order to prevent crack propagation advancement ...
Taheri, Sahid +10 more
core +1 more source
Applied Sciences, 2020 In industrial applications, the shafting components with high stress are easily damaged due to cyclic loads if there is no surface treatment. With the use of ultrasonic cavitation peening, the residual compressive stress and the surface hardness of these
Fushi Bai +5 more
doaj +1 more source
Microstructure Evolution of the Carbon Steels During Surface Severe Plastic Deformation
Успехи физики металлов, 2021 The review is devoted to the state-of-the-art views on the microstructure evolution in structural and tool carbon steels during the surface severe plastic deformation (SPD).
M. O. Vasylyev, B. M. Mordyuk, S. M. Voloshko, and D. A. Lesyk
doaj +1 more source
Effect of Ultrasonic Shot Peening on the Cavitation Erosion Resistance of SLM316L Stainless Steel [PDF]
Cailiao BaohuIn order to investigate the effect of ultrasonic shot peening on the cavitation erosion resistance of SLM316L stainless steel, the surface of SLM316L stainless steel was treated for varying durations (5, 25 and 45 min) using an ultrasonic shot peening ...
WANG Zenan, CHENG Feng, WANG Shuo, SUN Jie
doaj +1 more source
Effect of Ultrasonic Shot Peening on the Microstructure and Fatigue Properties of FGH99 Alloy [PDF]
Cailiao BaohuIn order to improve the high-temperature performance of turbine discs， an ultrasonic shot peening test was conducted on FGH99 alloy for turbine discs.The microstructure and fatigue properties of FGH99 alloy after ultrasonic shot peening treatment were ...
SONG Yinggang, LUO Xuekun, WANG Xin, FENG Yefei, TIAN Gaofeng
doaj +1 more source
Journal of Materials Research and Technology, 2023 Two passes of constrained groove pressing (CGP) were conducted on a two-phase Mg–Li alloy followed by temperature-assisted ultrasonic shot peening (TA-USP) with different peening durations and temperatures.
Meng Kong +6 more
doaj +1 more source