Results 51 to 60 of about 16,629 (343)

An Improved Scheduling Algorithm for Data Transmission in Ultrasonic Phased Arrays with Multi-Group Ultrasonic Sensors

Sensors, 2017
High data transmission efficiency is a key requirement for an ultrasonic phased array with multi-group ultrasonic sensors. Here, a novel FIFOs scheduling algorithm was proposed and the data transmission efficiency with hardware technology was improved ...
Wenming Tang, Guixiong Liu, Yuzhong Li, Daji Tan   +3 more
doaj   +1 more source

Performance of periodic piezoelectric composite arrays incorporating a passive phase exhibiting anisotropic properties [PDF]

, 2005
This paper explores the minimisation of interelement cross talk in 1-D and 2-D periodic composite array structures through the incorporation of a passive phase exhibiting anisotropic elastic properties.
Hayward, G., O'Leary, R.L., Parr, A.C.S., Pethrick, R.A., Troge, A.   +4 more
core   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

FEA-Based Ultrasonic Focusing Method in Anisotropic Media for Phased Array Systems

Applied Sciences, 2021
Traditional ultrasonic imaging methods have a low accuracy in the localization of defects in austenitic welds because the anisotropy and inhomogeneity of the welds cause distortion of the ultrasonic wave propagation paths in anisotropic media.
Seongin Moon, To Kang, Soonwoo Han, Kyung-Mo Kim, Hyung-Ha Jin, Sung-Woo Kim, Munsung Kim, Hyunil Seo   +7 more
doaj   +1 more source

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

Study of Residual Stress Using Phased Array Ultrasonics in Ti-6AL-4V Wire-Arc Additively Manufactured Components

Sensors
This paper presents a study on residual stress measurement in wire-arc additively manufactured (WAAM) titanium samples using the non-destructive method of phased array ultrasonics. The contour method (CM) was used for the verification of the phased array
Joseph Walker, Brandon Mills, Yashar Javadi, Charles MacLeod, Yongle Sun, Pradeeptta Kumar Taraphdar, Bilal Ahmad, Sundar Gurumurthy, Jialuo Ding, Fiona Sillars   +9 more
doaj   +1 more source

Algorithm of spatiomporal post-processing for ultrasonic tomography with phased arrays [PDF]

, 2018
Для решения задач ультразвукового контроля, связанных с повышением требований к достоверности полученных данных, сегодня используют перспективный метод, позволяющий визуализировать внутреннюю структуру объекта контроля.
Вдовенко, А. Ю., Долматов, Дмитрий Олегович   +1 more
core  

Ultrasound array transmitter architecture with high timing resolution using embedded phase-locked loops [PDF]

, 2012
Coarse time quantization of delay profiles within ultrasound array systems can produce undesirable sidelobes in the radiated beam profile. The severity of these sidelobes is dependent upon the magnitude of phase quantization error - the deviation from ...
Cowell, DMJ, Freear, S, Raiton, B, Smith, PR, Vo Ky, C   +4 more
core   +1 more source

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

Electroactive Metal–Organic Frameworks for Electrocatalysis

Advanced Functional Materials, EarlyView.
Electrocatalysis is crucial in sustainable energy conversion as it enables efficient chemical transformations. The review discusses how metal–organic frameworks can revolutionize this field by offering tailorable structures and active site tunability, enabling efficient and selective electrocatalytic processes.
Irena Senkovska, Yutong Luo, Ruyan Zhao, Jianjun Zhang, Mingchao Wang, Xinliang Feng, Eike Brunner, Stefan Kaskel   +7 more
wiley   +1 more source