Results 201 to 210 of about 5,544 (292)

Friction Stir Welding of Dissimilar Materials: A Review on Joining Mechanism, Defects, and Process Optimization. [PDF]

Materials (Basel)
Zhang Y, Wang S, Sun Y, Zhao C, Li W.
europepmc   +1 more source

Experimental and Comparative Study of the Corrosion Behavior of Lean Duplex Stainless Steel in Seawater

Materials and Corrosion, EarlyView.
The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh, Nicolas Larché, Audrey Allion‐Maurer, Raf Dewil, Barbara Rossi   +4 more
wiley   +1 more source

A Deep Learning-Based Method for Stress Measurement Using Longitudinal Critically Refracted Waves. [PDF]

Sensors (Basel)
Gan Y, Ma J, Zhang B, Zheng Y, Wang X, Zhu Y, Wang Y, Ji D.   +7 more
europepmc   +1 more source

Development and simulation of a novel mathematical model for an intelligent tire system toward predictive maintenance. [PDF]

Sci Rep
Hijry H, Mohsen S, Albalawi O, Ali S, Alhawiti A, Elnashar GA.   +5 more
europepmc   +1 more source

Influence of Strain Rate on the Strain Hardening Behavior of a Lean Duplex Stainless Steel

MetalMat, EarlyView.
The aim of this study was to examine how strain rate influences the compressive strain‐hardening behavior of a lean duplex stainless steel LDX 2101. Microstructural analysis using electron backscatter diffraction (EBSD) revealed a strain‐induced austenite‐to‐martensite transformation.
Akilakps Sawyerr, Eric Kotei T. Addison, Martin Owusu‐Mensah, Abdul Jaleel Mohammed, Daolun Chen   +4 more
wiley   +1 more source

Effect of Cold Rolling on the Mechanical Properties and Corrosion Resistance in Hydrofluoric Acid Solution of Inconel 600 Alloy. [PDF]

Materials (Basel)
Dong X, Li Y, Shang R, Chen M, Liu L, Teng J, Li Y.   +6 more
europepmc   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

A modular, multi-sensor crawler robot for adaptive pipeline inspection: design and experimental validation. [PDF]

Sci Rep
Eltwab AAA, Sameh A.
europepmc   +1 more source

A Review of Mechanical Reinforcement and Piezoresistive Self‐Sensing in Carbon Nanotube Fiber Composites

Polymer Composites, EarlyView.
PSPP‐TRL mapping of CNT‐modified CFRP literature, with four recurring confusions resolved and five scale‐up problems quantified. ABSTRACT Carbon nanotube‐modified fiber composites are often presented as a route to stronger, tougher, and self‐sensing structural materials.
Sanan H. Khan
wiley   +1 more source

Defect Analysis of Surface Cracks in Mn18Cr2 High-Manganese Wear-Resistant Steel Plate. [PDF]

Materials (Basel)
Yang D, Zhang N, Liu Z, Jiang B.
europepmc   +1 more source