Ultrasonic measurement of stress in 2219-T87 aluminum plate [PDF]
The basic relationship of ultrasonic signal velocity to directional subsurface stress is reviewed. Inappropriateness of dependency on a single correlative value of constant for a three dimensional stress field in metallic materials is discussed ...
Clotfelter, W. N., Risch, E. R.
core +1 more source
A comparative study of using static and ultrasonic material testing methods to determine the anisotropic material properties of wood [PDF]
, 2016 © 2015 Elsevier Ltd. This paper presents a comparative study using static and ultrasonic testing for the determination of the full set of orthotropic material properties of wood.
Crews, K +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Correlations among ultrasonic propagation factors and fracture toughness properties of metallic materials [PDF]
Empirical evidence was developed to show that a close relation exists among fracture toughness, yield strength, and ultrasonic attenuation properties of metallic materials.
Vary, A.
core +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Jixie chuandong, 2013 The internal flaws in gearswhich occur during manufacturing and service have great effect on operation safety of equipments.A scheme of automatic ultrasonic testing based on the XYmotion platformis presented,and the corresponding automatic ultrasonic ...
吕铎, 杨岳, 李雄兵, 刘希玲
doaj
Input-output characterization of an ultrasonic testing system by digital signal analysis [PDF]
The input/output characteristics of an ultrasonic testing system used for stress wave factor measurements were studied. The fundamentals of digital signal processing are summarized.
Karaguelle, H. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Transient Propagation and Scattering of Quasi-Rayleigh Waves in Plates: Quantitative comparison between Pulsed TV-Holography Measurements and FC(Gram) elastodynamic simulations [PDF]
, 2019 We study the scattering of transient, high-frequency, narrow-band quasi-Rayleigh elastic waves by through-thickness holes in aluminum plates, in the framework of ultrasonic nondestructive testing (NDT) based on full-field optical detection.
Amlani, Faisal +6 more
core +1 more source
Interaction of laser generated ultrasonic waves with wedge-shaped samples [PDF]
, 2012 Wedge-shaped samples can be used as a model of acoustic interactions with samples ranging from ocean wedges, to angled defects such as rolling contact fatigue, to thickness measurements of samples with non-parallel faces.
A. R. Clough +7 more
core +1 more source