Results 21 to 30 of about 27,924 (214)

Research on heat transfer characteristics and cold trap capacity of a water catcher during vacuum pre-cooling

IOP Conference Series: Earth and Environmental Science, 2017
Effect of vacuum pre-cooling process on apples was a complex process of heat and mass transfers. The research is based on the physical properties of apples and their heat and mass transfer mechanisms during vacuum pre-cooling. As for the heat transfer characteristics of a water catcher in vacuum pre-cooling, the research studied the heat transfer ...
Enhai Liu, Yin Liu, Changzhong Wang, Shiqi Liu   +3 more
openaire   +1 more source

A novel quinazolinone insulin receptor inhibitor and its synergy with an EGFR inhibitor in glucose‐driven glioblastoma

Molecular Oncology, EarlyView.
The novel styrylquinazolinone‐based molecule W1B effectively suppresses glioblastoma by inhibiting IGF1R and EGFR. In high‐glucose microenvironments driving tumor resistance, W1B acts synergistically with the EGFR inhibitor dacomitinib. This combination safely blocks compensatory survival signaling in zebrafish xenograft models. Showcasing promising in
Patryk Rurka, Wioleta Cieślik, Wojciech Płaziński, Katarzyna Stępnik, Anna Boguszewska‐Czubara, Elżbieta Kot, Robert Musioł, Mateusz Jasica, Anna Mrozek‐Wilczkiewicz, Katarzyna Malarz   +9 more
wiley   +1 more source

Dose‐dependent hepatotoxicity of hydrogen peroxide in HepG2 cells and its modulation by CYP450 induction

FEBS Open Bio, EarlyView.
NMR metabolomics revealed concentration‐dependent metabolic perturbations in HepG2 cells exposed to H2O2. Rifampicin pretreatment enhanced metabolic competence, attenuated toxin‐induced alterations and produced metabolite profiles more consistent with human liver physiology, supporting the use of CYP450‐induced HepG2 models for improved in vitro ...
Maren Jinks, Garth L. Maker, Emily C. Davies, Berin A. Boughton, Samantha Lodge   +4 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Investigation of Electromagnetic Sub-Modeling Procedure for the Breeding Blanket System

Journal of Nuclear Engineering, 2023
The outcome of the electromagnetic (EM) analyses carried out during the DEMO pre-conceptual phase demonstrated that EM loads are relevant for the structural assessment of the breeding blanket (BB) and, in particular, for the definition of the boundary ...
Ivan Alessio Maione, Massimo Roccella, Flavio Lucca   +2 more
doaj   +1 more source

Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing

Advanced Engineering Materials, EarlyView.
This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu, Xun Zhang, Jack M. Donoghue, Albert D. Smith, Rahul Unnikrishnan, Rhys Thomas, Vahid Nekouie, Jie Luo, Dongchen Hu, Michael Preuss, Philip J. Withers   +10 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators

Advanced Engineering Materials, EarlyView.
A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad, Aleksander Kostka, Gowtham Arivanandhan, Yujiao Li, Alan Savan, Manfred Kohl, Alfred Ludwig   +6 more
wiley   +1 more source