Results 91 to 100 of about 118,476 (265)

4D Printing of Multimaterial Flexible Magneto‐Active Polymers

Advanced Materials Technologies, EarlyView.
Magneto‐active polymers are 3D‐printed with tunable mechanical and magnetic properties using both superparamagnetic and hard ferromagnetic fillers. Nano‐CT imaging reveals the spatial distribution of particles within the matrix. Programmable magnetization patterns and soft, flexible architectures enable responsive actuation, offering exciting ...
Naji Tarabay, Mahtab Shakibmanesh, Javier Alonso López Medina, Hongyi Guan, Alan Mitchell, Ananya Renuka Balakrishna, Camilo Velez   +6 more
wiley   +1 more source

Characterization and Design Framework for Micro‐ and Nanoscale Printed Metal Interconnects in Hybrid Electronic Systems

Advanced Materials Technologies, EarlyView.
This work establishes a framework for high‐resolution printed interconnects by coupling e‐jet printing control, multilayer deposition, and sintering optimization. Ink properties and printing speed influence particle stacking, while different sintering atmospheres drive distinct microstructural evolution.
Kaifan Yue, Siddharth Kurup, Rebecca Banner, Calib Lanier, Eric Vogel, Michael Filler, Kira Barton   +6 more
wiley   +1 more source

Vat photopolymerization of ultra-porous bioactive glass foams

Open Ceramics
The introduction of additive manufacturing technologies in the field of biomaterials science has opened new horizons for regenerative medicine. In this work, we pushed the potential of vat polymerization to the limit for fabricating ultra-porous ...
Francesco Baino, Federico Gaido, Roberta Gabrieli, Dario Alidoost, Alessandro Schiavi, Mehdi Mohammadi, Martin Schwentenwein, Dilshat Tulyaganov, Enrica Verné   +8 more
doaj   +1 more source

Sustainable Value Roadmapping Framework for Additive Manufacturing [PDF]

, 2018
This is the final version of the article. Available from Elsevier via the DOI in this record.24th CIRP Conference on Life Cycle Engineering, 8-10 May 2017, Kamakura, JapanRecent developments around the use of additive manufacturing (AM) for making ...
Despeisse, M, Evans, S, Ford, S, Minshall, T, Yang, M   +4 more
core   +1 more source

3D Printed PEDOT:PSS‐Based Lattice Pressure Sensors With Tunable Electromechanical Response

Advanced Materials Technologies, EarlyView.
poly(3,4‐ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS)‐based architected lattices are fabricated via single‐step Digital Light Processing (DLP) printing for tunable pressure sensing. Structural design variations allow precise control of sensitivity and range, while integrated conductivity eliminates post‐processing.
Ozan Karakaya, Naroa Lopez‐Larrea, Ali Veysel Tunc, Mikel Rincon‐Iglesias, Karin J. Chen, Katja Nau, Senentxu Lanceros‐Mendez, David Mecerreyes, Miryam Criado‐Gonzalez, Gerardo Hernandez‐Sosa   +9 more
wiley   +1 more source

Nitroxide‐Mediated Photo‐Polymerization: A Swiss Army Knife for Microfluidic Design

Advanced Materials Technologies, EarlyView.
This article illustrates the application of NMP2 to the rapid (less than 1 h) photostructuring and sealing of model structures intended for microfluidic applications. Remarkably, the careful design of resin composition allows completing these steps by simply spreading bare monomer (i.e., no added photoinitiator) on top of the bottom layer embedding ...
Carlo Gonzato, Sandip Wadhai, Jean‐Louis Clement, Florent Malloggi, Yohann Guillaneuf, Olivier Soppera   +5 more
wiley   +1 more source

Suppression of the leading-edge bulge effect in ceramic vat photopolymerization via yield stress regulation for enhanced part performance

Additive Manufacturing Letters
This study addresses the ''leading-edge bulge effect'' encountered during the ceramic slurry recoating stage in ceramic vat photopolymerization by regulating the slurry’s yield stress to suppress backflow.
Ning Wang, Chi Zhang, Hai Chang, Dongxu Yao, Zirong Zhai, Rui Yang   +5 more
doaj   +1 more source

The 3D printing order: variability, supercenters and supply chain reconfigurations [PDF]

, 2016
This is the accepted and refereed manuscript to the articlePurpose: Direct Digital Manufacturing (DDM) is conceived of as either disrupting the entire manufacturing economy or merely enabling novel production.
Johnson, John Chandler, Sasson, Amir
core   +3 more sources

Multi‐Material Additive Manufacturing of Soft Robotic Systems: A Comprehensive Review

Advanced Robotics Research, EarlyView.
This review explores the transformative role of multi‐material additive manufacturing (MMAM) in the development of soft robotic systems. It presents current techniques, materials, and design strategies that enable functionally graded and adaptive structures.
Ritik Raj, Quan‐Chen Song, Jia‐Yang Juang   +2 more
wiley   +1 more source

3D Printing of Soft Robotic Systems: Advances in Fabrication Strategies and Future Trends

Advanced Robotics Research, EarlyView.
Collectively, this review systematically examines 3D‐printed soft robotics, encompassing material selections, function integration, and manufacturing methodologies. Meanwhile, fabrication strategies are analyzed in order of increasing complexity, highlighting persistent challenges with proposed solutions.
Changjiang Liu, Bin Cui, Xumin Huang, Xiaoyu (Rayne) Zheng, T. Thang Vo‐Doan, Ruirui Qiao   +5 more
wiley   +1 more source