Results 101 to 110 of about 3,076 (205)

Enhancing the Tribological Performance of PLA via Process‐Induced Functional Grading in Masked Stereolithography

Polymer Engineering &Science, Volume 66, Issue 6, Page 4724-4737, June 2026.
An exposure‐time‐controlled MSLA fabrication strategy enabling filler‐free functionally graded polymers, resulting in up to a 62% reduction in specific wear rate. ABSTRACT Masked stereolithography (MSLA) enables high‐resolution fabrication of photopolymer components; however, the limited tribological performance of neat resins restricts their ...
Muhammet Mevlüt Karaca, Abdurrahim Temiz, Fatih Huzeyfe Öztürk   +2 more
wiley   +1 more source

AI for AM: machine learning approach to design the base binder formulation for vat-photopolymerisation 3D printing of zirconia ceramics

Virtual and Physical Prototyping
Additive manufacturing of ceramics, specifically through vat-photopolymerization, offers significant potential due to its high precision and ability to produce complex geometries.
Fatih Tarak, Leah Okoruwa, Basar Ozkan, Farzaneh Sameni, Gerald Schaefer, Ehsan Sabet   +5 more
doaj   +1 more source

Development of methodology for multi-material VAT photopolymerization printing

This study aims to develop a methodology for multi-material vat photopolymerization printing and conceptualize a viable prototype with a reduced footprint.
Niyagama Gamage, Wudith
core  

Valorization of Poplar Wood Wastes Into 3D‐Printed Soya Oil‐Based Composites by Vat Photopolymerization for Interior Design

Journal of Polymer Science, Volume 64, Issue 11, Page 2351-2367, 1 June 2026.
Bio‐based polymer composites were 3D printed by LCD vat photopolymerization using acrylate epoxidized soybean oil as the monomer and isobornyl methacrylate as the reactive diluent. Two different poplar powders derived from plywood processing waste were incorporated within the photocurable formulations.
Francesca Sacchi, Tiziano Uriel Monteu Cotto, Giovanna Colucci, Guido Callegari, Paolo Simeone, Daniela Bosia, Federica Bondioli, Massimo Messori   +7 more
wiley   +1 more source

Recent advances in design and preparation of bioceramic materials for manufacturing dental crowns by vat photopolymerization

Discover Applied Sciences
The most durable and acceptable tooth-colored crown material should have good physical, and mechanical properties, chemical resistance, biocompatibility, and aesthetic behavior.
Adel Osama, Noha Fouda, Mohamed T. Eraky
doaj   +1 more source

Machine learning assisted material development for lithography-based additive manufacturing of porous alumina ceramics

Open Ceramics
The transition of applying ceramic additive manufacturing (AM) from prototyping to mass production and from monolithic to multi-material (MM) components can be supported by continual development in materials and processes.
Serkan Nohut, Martin Schwentenwein
doaj   +1 more source

Ink‐Printed Thermoelectric Materials and Devices: Material Preparation, Fabrication Techniques, and Applications

Small Science, Volume 6, Issue 6, June 2026.
Ink‐printing technique is promising in fabricating thermoelectric materials and devices for advanced wearable electronics applications. Thermoelectric (TE) materials, which enable the direct conversion between thermal and electrical energy, represent a promising solution for sustainable energy technologies.
Juxiang Shao, Lin Li, Ming Yang, Jiali Huang, Na Zhang, Supree Pinitsoontorn, Qiang Sun, Hongchun Luo, Hao Wu   +8 more
wiley   +1 more source

3D‐Printed Na3V2(PO4)3 Electrodes for Symmetric Sodium‐Ion Batteries

Small Structures, Volume 7, Issue 6, June 2026.
Vat photopolymerization 3D printing is used to fabricate current collector‐free Na3V2(PO4)3 (NVP) electrodes with complex lattice geometries. After thermal postprocessing, the printed electrodes operate reversibly as both positive and negative electrodes in a symmetric sodium‐ion battery.
Ana C. Martinez, Sina Bakhtar Chavari, Christian A. Ruiz, Myeong‐Lok Seol, Donald A. Dornbusch, William H. Huddleston, Felicia S. Manciu, Bharat Yelamanchi, Tommy Rockward, Pedro Cortes, Cadré Francis, Carol Putman, Alexis Maurel   +12 more
wiley   +1 more source

Characterization of Spatially Variant Electromechanical Properties in a 3D Printed Architected Piezoceramic

International Journal of Applied Ceramic Technology, Volume 23, Issue 3, June 2026.
The article describes a methodology to obtain spatial map of full piezoelectric tensor of an architected polycrystalline piezoceramic, based on direct knowledge of microstructural changes that is gained through in situ X‐ray microdiffraction and further complemented by micromechanical computations.
Abhijit Pramanick, David Hall, Laurent Daniel, Yizhe Li, Chaimae Babori, Frédéric Albertini, Frederik Holm Gjørup, Mads Ry Vogel Jørgensen   +7 more
wiley   +1 more source

Are bio‐based resins suitable alternatives for additively manufactured removable dies? An in vitro study on dimensional and positional trueness and stability

Journal of Prosthodontics, Volume 35, Issue 5, Page 732-742, June 2026.
Abstract Purpose This study aimed to compare the dimensional and positional deviations of additively manufactured removable dies fabricated using two bio‐based resins and one conventional dental cast resin, while also evaluating these outcomes over a 4‐week period.
Mustafa Borga Dönmez, Clara Lisa Soliva, Hanan Al‐Johani, Ahmet Orgev, Martin Schimmel, Gülce Çakmak, Burak Yilmaz   +6 more
wiley   +1 more source