Results 111 to 120 of about 9,831 (263)

Influence of Carbon Nanoparticles on Electrically Induced Wear of Grease‐Lubricated Steels

Advanced Materials Interfaces, EarlyView.
When an electric current enters a pair of rubbing surfaces, enormous damage takes place. In this research, how such damage occurs in the presence of protective grease and the mitigation with added carbon nanoparticles, were investigated. It was discovered that those particles regulate transport and interfacial electrical stability of the grease ...
Mohammad Humaun Kabir, Darrius Dias, Jacob Bons, MD Wasek Foysal, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Network Slice-Enabled Federated Learning for Collaborative Traffic Perception in Vehicular Edge Computing

IEEE Access
This paper presents a novel network slice-enabled federated learning framework for collaborative traffic perception in vehicular edge computing environments.
Xu He, Peizhi Sheng, Bohao Tao, Wenhao Li   +3 more
doaj   +1 more source

Minimally Invasive Delivery of Optical Nanosensors Using Injectable Hydrogels

Advanced Materials Interfaces, EarlyView.
Injectable peptide hydrogels offer a minimally invasive delivery platform for single‐walled carbon nanotube (SWCNT)‐based near‐infrared fluorescent sensors, enabling real‐time measurement of drug concentrations. Encapsulated SWCNTs show a dose‐dependent fluorescence response across physiologically relevant concentrations and retain their fluorescence ...
Shirel Kleiner, Gili Bisker
wiley   +1 more source

On the Friction and Wear Mechanisms of Electrified Steel Contacts in CO2: Unveiling the Role of Carbon‐Rich Tribofilms Under Dry Sliding Conditions

Advanced Materials Interfaces, EarlyView.
This study investigates friction and wear of AISI 52100 steel under dry sliding in CO2, air, and N2 atmospheres, with and without contact electrification. CO2 forms a stable carbon‐rich tribofilm that reduces friction by ∼30% and wear by ∼85%. High‐resolution TEM, EELS, and molecular dynamics reveal pressure‐dependent lubrication mechanisms, showing ...
Julio A. Cao‐Romero‐Gallegos, Seungjoo Lee, Cagatay Yelkarasi, Leonardo I. Farfan‐Cabrera, Ryuichi Okamoto, Hitoshi Washizu, Ali Erdemir   +6 more
wiley   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

The Influence of Mesoscale Particle Structure on the Electrode Degradation and Resultant Electrochemistry of Lithium Ion Cells With Nickel Rich Lithium Nickel Manganese Cobalt Oxide Positive Electrodes

Advanced Materials Technologies, EarlyView.
Milled polycrystalline NMC811 cathode (MPC NMC) with smaller secondary particle and higher surface area had 1) greater cathode tortuosity, 2) reduced surface Ni on the cycled MPC cathodes consistent with surface reconstruction, and 3) increased Ni deposition from cathode‐anode crosstalk, manifesting in lower functional capacity and higher impedance ...
Edelmy J. Marin Bernardez, Andrew Nicoll, David J. Arnot, Armando Rodriguez Campos, Patrick J. Barry, Marie F. Millares, Cynthia Huang, Melissa A. Guercio, Grace K. Dono, Alexis Pace, Xianghui Xiao, Cherno Jaye, Conan Weiland, Jianming Bai, Hui Zhong, Michael Drakopoulos, Zhong Zhong, Nghia T. Vo, Xiao Tong, Esther S. Takeuchi, Amy C. Marschilok, Shan Yan, Kenneth J. Takeuchi   +22 more
wiley   +1 more source

Three‐Dimensional Printed Microarchitected Hierarchically Porous Biodegradable PLA/S/CNT Nanocomposite Electrodes for High‐Performance Lithium–Sulfur Batteries

Advanced Materials Technologies, EarlyView.
Hierarchically microarchitected PLA/S/CNT cathodes are fabricated via scalable fused filament 3D printing as high‐sulfur‐loading hosts for rechargeable lithium–sulfur batteries. The assembled Li–S cells with sulfur loadings up to 17 mg cm−2 deliver an areal capacity of 9.2 mAh cm−2 and retain 96% of their discharge capacity after 100 charge–discharge ...
Vinay Gupta, Pawan Verma, Fahad Alam, Krishnaiahnahundi Manjunathaswamy Mohan, Shanumgam Kumar   +4 more
wiley   +1 more source

Biodegradable Wireless Soil Urea Sensor Using Metamaterial Perfect Absorber for Distributed Deployment in Precision Agriculture

Advanced Materials Technologies, EarlyView.
In this study, we propose a biodegradable wireless soil urea sensor for precision agriculture. The sensor's electromagnetic response varies depending on the urea concentration, allowing the measurement of relative soil urea concentrations by analyzing the time‐transient electromagnetic response.
Yu Tanaami, Ken Sakabe, Tetsuya Yarimizo, Yasutaka Murakami, Tetsuo Kan, Hiroaki Onoe   +5 more
wiley   +1 more source

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

Advanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee, Rocco Lupoi, Michael J. Gibbons   +2 more
wiley   +1 more source

Network Service and Resource Orchestration: A Feature and Performance Analysis within the MEC-Enhanced Vehicular Network Context. [PDF]

Sensors (Basel), 2020
Slamnik-Kriještorac N, Silva EBE, Municio E, Resende HCC, Hadiwardoyo SA, Marquez-Barja JM.   +5 more
europepmc   +1 more source