Results 251 to 260 of about 369,920 (316)

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Study on mechanism of air distribution volume's influence on airflow, dust migration and spray dust reduction in fully mechanized caving face. [PDF]

Sci Rep
Hongjie Z, Shaocheng G, Tian Z, Deji J, Xi C, Xingyu C.   +5 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

A direct black-hole mass measurement in a little red dot at high redshift. [PDF]

Nature
Juodžbalis I, Marconcini C, D'Eugenio F, Maiolino R, Marconi A, Übler H, Scholtz J, Ji X, Jones GC, Perna M, Arribas S, Bennett JS, Bromm V, Bunker AJ, Carniani S, Charlot S, Cresci G, Dayal P, Egami E, Fabian A, Inayoshi K, Isobe Y, Ivey LR, Koudmani S, Laporte N, Liu B, Lyu J, Mazzolari G, Monty S, Parlanti E, Pérez-González PG, Robertson B, Schneider R, Sijacki D, Tacchella S, Trinca A, Valiante R, Volonteri M, Witstok J, Zhang S.   +39 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Early cerebral palsy risk screening through wearable accelerometry in infants under nine weeks. [PDF]

Sci Rep
Alvarado J, Moreno G, Arancibia F, Marín-Palma M, Rojas-Sepulveda I, Becerra-Caroca J, Zepeda R, Jacobson R, Burgos PI.   +8 more
europepmc   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Effects of Flow Distributor Position and Loosener Configuration on Particle Flow Behavior in a Hydrogen-Based Direct Reduction Shaft Furnace. [PDF]

Materials (Basel)
Xue Q, Liao H, Zhao Q, Ji A, Huang D, Zhao G, Jiang C, Zhang J, Li K.   +8 more
europepmc   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Computational insight to optimize nanofluidic thermal transport management in octagonal enclosure with heat generating element by envisioning novel physical factors. [PDF]

Discov Nano
Ullah A, Khan NZ, Bilal S, Riaz MB.
europepmc   +1 more source