Results 101 to 110 of about 913,493 (290)
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Identifying codes in vertex-transitive graphs and strongly regular graphs [PDF]
, 2015 We consider the problem of computing identifying codes of graphs and its fractional relaxation. The ratio between the size of optimal integer and fractional solutions is between 1 and 2ln(vertical bar V vertical bar) + 1 where V is the set of vertices of
Gravier, Sylvain +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Tam protez kullanan hastalarda doğal baş-boyun postürünün ve dik yön boyutlarının değerlendirilmesi
European Annals of Dental Sciences, 2008 Diş çekimlerini takip eden alveoler kemikrezorpsiyonuna bağlı olarak mandibulanın öne veyukarı yer değiştirmesi çeneler arası ilişkilerdedeğişikliğe neden olur.
Sezer Şen, Betül Kalıpçılar
doaj
Life and ScienceObjective: The purpose of this study is to compare changes in occlusal vertical dimension when dental plaster versus dental stone is used as the investing material. Study Design: Comparative experimental study. Place and Duration of Study: This study was
Samina Memon +6 more
doaj +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Does vertical pattern affect lip strain in open-bite patients?: A cephalometric study
Adıyaman Üniversitesi Sağlık Bilimleri DergisiAim: To examine effect of skeletal pattern on lip strain in open-bite, in individuals with normal and increased vertical pattern.Materials and Methods: 56 open bite patients with Normovergent (NG) and Hyperdivergent (HG) vertical patterns (Mean age: 16 ...
Ece Başal +2 more
doaj +1 more source
Localisation of the unerupted maxillary canine: further observations
Australasian Orthodontic Journal, 1998 This paper discusses the interpretation of radiographs taken to localise impacted maxillary canines. In particular, the sometimes unexpected radiographic appearance of labially impacted canines is explained.
Jacobs Stanley G.
doaj +1 more source