Results 81 to 90 of about 722,630 (301)
Fault slip-rate variations during crustal-scale strain localisation, central Italy [PDF]
, 2002 Rates of plate motion are generally uniform over 10–102 Myrs timescales. Faults between tectonic plates might, therefore, be expected to show temporally-uniform slip-rates if the same number of faults remain active. For an extending region of the Eurasia-
Cowie, P +4 more
core
Fluid Biomarkers of Disease Burden and Cognitive Dysfunction in Progressive Supranuclear Palsy
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objective Identifying objective biomarkers for progressive supranuclear palsy (PSP) is crucial to improving diagnosis and establishing clinical trial and treatment endpoints. This study evaluated fluid biomarkers in PSP versus controls and their associations with regional 18F‐PI‐2620 tau‐PET, clinical, and cognitive outcomes.
Roxane Dilcher +10 more
wiley +1 more source
Biomechanical Study of Posterior Pelvic Fixations in Vertically Unstable Sacral Fractures: An Alternative to Triangular Osteosynthesis [PDF]
Asian Spine Journal, 2018 Study Design Biomechanical study. Purpose To investigate the relative stiffness of a new posterior pelvic fixation for unstable vertical fractures of the sacrum.
Weera Chaiyamongkol +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Quantifying the onset of the concentric phase of the force–time record during jumping [PDF]
, 2009 Thirteen college students performed a drop jump from height equal to their peak vertical jump, single leg jumps from the left and right legs, and a counter movement jump.
Ebben, William +4 more
core +2 more sources
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
TINJAUAN STABILITAS JEMBATAN RANGKA BAJA TERBUKA DENGAN GARIS KERJA GAYA BATANG YANG TIDAK SENTRIS (Studi kasus pada model jembatan KJI : Apple Bridge) [PDF]
, 2009 Bridge represent element / part of road, that is a construction as transportation link medium between road which is one with other which blocked by barricade in the form of river, creavasse, bog, strait and others.
MUTTAQIEN, SHOBBAH SABILIL
core
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
, 1973 A tin oxide coating is formed on a plate of glass and the coating is then etched away from the glass in thin lines to form separate electrical conductors which extend to one end of the plate and connect to either a vertical (column) or horizontal (row ...
Rasmussen, H. P.
core +1 more source