Results 21 to 30 of about 865,855 (214)
Ground vibration measurements with special reference to pile driving [PDF]
, 1990 There has been increased concern in recent years over the level and nature of the ground vibrations. The importance of such vibration has increased rapidly due to developments in construction in urban areas, where the effects of ground borne vibration on
Uromeihy, Ali, Uromeihy, A
core
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Development of LRFD Procedures for Bridge Pile Foundations in Iowa, September 2011 [PDF]
, 2011 In response to the mandate on Load and Resistance Factor Design (LRFD) implementations by the Federal Highway Administration (FHWA) on all new bridge projects initiated after October 1, 2007, the Iowa Highway Research Board (IHRB) sponsored these ...
core
Vibratory driving of piles and sheet piles-state of practice
, 2022 The installation of piles by vibratory methods is discussed and illustrated by case histories. The influence of vibration frequency - which can be controlled during vibratory driving but not during impact driving - on pile penetration, bearing capacity ...
Wersäll, Carl, +2 more
core +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Analysis of a rapid load test on an instrumented bored pile in clay [PDF]
, 2006 Rapid load testing methods for piled foundations are generally easier and quicker to mobilise than classic static tests, and are less complex to analyse than dynamic load tests.
Brown, M. J.; id_orcid +2 more
core +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Tạp chí Khoa học và Công nghệAccurately determining the effective impact radius of construction-induced vibrations, such as those caused by vibratory roadbed compaction, pile driving, and rock blasting, is essential for ensuring the safety of adjacent structures and minimizing ...
Thai Hoang An +2 more
doaj +1 more source
Development of LRFD Procedures for Bridge Pile Foundations in Iowa: Volume II: Field Testing of Steel Piles in Clay, Sand, and Mixed Soils and Data Analysis, September 2011 [PDF]
, 2011 In response to the mandate on Load and Resistance Factor Design (LRFD) implementations by the Federal Highway Administration (FHWA) on all new bridge projects initiated after October 1, 2007, the Iowa Highway Research Board (IHRB) sponsored these ...
core