Results 91 to 100 of about 2,539 (294)
Advanced Engineering Materials, EarlyView.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
The study of warp tension in weauing machine (No.2)
Journal of the Textile Machinary Society, 1952 研究目的筬打前後の経糸張力の変化、筬打位置に緯糸が安定する條件及び経糸張力が織物の厚さに及ぼす影響を考察する。研究結果問題を数式的に取扱い次の結果を得た。1) 緯糸は織巾の全体にわたり略同一張力。2) 筬打時の経糸張力増加率を表わす式。3) 筬打に要する力を表わす式。4) 緯糸が打込位置に安定するか否かを判別する式。5) 経糸張力と織物の厚さとの関係を表わす式。以上の諸式を誘導した。
Miura, Yoshito, Uno, Minoru
openaire +3 more sources
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
, 2011 This paper assesses warp tension distribution over the warp width and its effect on fabric's breaking strength distribution over the fabric width in plain woven fabrics.
core
The sea trials study of warp tension for trawlers based on dynamic and data-driven models
Applied Ocean ResearchAs the importance of intelligence and automation grows across various domains, there is an increasing demand for intelligent applications in trawler fishing.
Panpan Jia +4 more
doaj +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Loom Speed and Tension to Reduce Warp and Weft Breaks in Air Jet Weaving
, 2012 Loom Speed and Tension to Reduce Warp and Weft Breaks in Air Jet Weaving is a published article of the Textile Technology department.,The study sought to identify correct values of loom speed and warp tension suitable for weaving 100% cotton yarn on ...
Nkiwane, Londiwe
core
The Effect of Backrest Roller on Warp Tension in Modern Loom
, 2017 The Backrest roller is one of the key parts of the weaving machine. In this study, the effect of the various position of backrest and dropper has been assessed. The tension is measured by using the integrated tension measuring device of the loom.
Toufique Ahmed +5 more
core +1 more source