Results 61 to 70 of about 2,539 (294)
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Monitoring of the Variation in Pore Sizes of Woven Geotextiles with Uniaxial Tensile Strain
Applied Sciences, 2021 Characteristic pore-opening size O95 or O90 has been widely used in the filter design of woven geotextiles. These manufactured products have different pore size proportions of large pore diameters, medium pore diameters, and small pore diameters ...
Wenfang Zhao +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
EFFECTS OF TENSION VARIATIONS OF INDIVIDUAL YARNS ON QUALITY OF WARP KNITTED FABRICS
, 2017 <p>Yarns of warp beams to knit on warp knitting machines need to be wound at equal tensions. The tension variations lead to produce valleys and ridges of warp yarns on the beam and hence different lengths of individual warp yarns.
Lanarolle, W.D.G.*, Weerasooriya, W.M.N, Madushika, K.S.M and Tharsan G
core +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
A Study on Stabilization of Warp Tension on Loom
Journal of the Textile Machinary Society, 1957 研究目的織機の毎製織サイクル中に起る経糸張力の変化を検討し, 開口による経糸長の変動補整装置を改善, 張力を安定化して経糸切断, 経糸異状伸長等の因子を除去し品質を向上させることを目的とする.研究結果運転中の経糸張力を抵抗線ひずみ型張力計を通じ, 電磁オシログラフに記録して得た結果より次の諸事項を知り得た.1) 従来のパックレストによるイージングモーションは, 経糸張力変動に対し余り有効には補整作用を行っていない.2) 試作補整装置の作用は極めて有効であり, 張力変動率は従来の約1/4であった.3) 経糸有効総長の増加は張力安定化に相当寄与している.4) イージングローラ回りの慣性モーメントはかなり大きい.
Kimura, M., Oshima, K.
openaire +2 more sources
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
The calculation of warping spools of warp-knitting machines
Trudy Odesskogo Politehničeskogo Universiteta, 2014 The paper is devoted to the development of scientific bases of the knitting machine design, in particular, to the calculation of warping spools of warp-knitting machines.
Vitaliy V. Chaban, Boris F. Pipa
doaj +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source