Results 51 to 60 of about 136,219 (309)
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
EPJ Web of Conferences, 2016 A polybenzimidazole (PBI) based polymer electrolyte fuel cells, which called high temperature polymer electrolyte fuel cells (HT-PEMS), operate at higher temperatures (120-200°C) than conventional PEM fuel cells.
Celik Muhammet +3 more
doaj +1 more source
Zaporožskij Medicinskij Žurnal, 2018 The purpose of the work is to investigate the range of renoprotection, in particular osmotic and volumoregulatory functions, with combined application of sorbitol and L-arginine in patients with endogenous intoxication syndrome of purulent-septic genesis
V. M. Konovchuk , N. O. Maksymchuk
doaj +1 more source
Modeling and simulations of deformation and transport in PEM fuel cells [PDF]
, 2008 Performance degradation and durability of PEM fuel cells depend strongly upon transport and deformation characteristics of their components especially the polymer membrane.
Yesilyurt, Serhat, Yeşilyurt, Serhat
core +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Experimental validation of equilibria in fuel cells with dead-ended anodes [PDF]
, 2013 This paper investigates the nitrogen blanketing front during the dead-ended anode (DEA) operation of a PEM fuel cell. Surprisingly the dynamic evolution of nitrogen and water accumulation in the dead-ended anode (DEA) of a PEM fuel cell arrives to a ...
Chen, Jixin +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
A Dual‐Cation Exchange Membrane Electrolyzer for Continuous H2 Production from Seawater
Advanced ScienceDirect seawater splitting (DSS) offers an aspirational route toward green hydrogen (H2) production but remains challenging when operating in a practically continuous manner, mainly due to the difficulty in establishing the water supply–consumption ...
Yongwen Ren +8 more
doaj +1 more source
Purification of Tannery Effluent by electrolytic corrosion of aluminium [PDF]
, 2006 Tannery Effluent is noxious because tanning process chemicals are preservatives, including chromium, and the pH is high. Electrolytic processing is feasible because the high salt content gives a high electrical conductivity. While research on the subject
Jamieson, Graham +2 more
core +2 more sources
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source