Results 221 to 230 of about 5,338,399 (290)

Linking geochronology and source apportionment of sediments to understand land-lake transfers in the Lake Victoria Basin. [PDF]

Environ Geochem Health
Watts MJ, Humphrey OS, Tuffield L, Gowing C, Marriott AL, Ongore CO, Isaboke J, Osano O, Blake WH, Aura CM.   +9 more
europepmc   +1 more source

Hierarchical Multi‐Material Architectures With Gradient Design for Dynamic‐Range Flexible Tactile Sensing

Advanced Materials Technologies, EarlyView.
Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi, Domenic Quiquero, Yan Yan Shery Huang, HaoTian Harvey Shi   +3 more
wiley   +1 more source

Experimental study on the sand discharge characteristics of a swirling sand dredging device in a reservoir area with multiple mud and sand rivers. [PDF]

Sci Rep
Wang Z, Wang Y, Xi H, Luo T, Miao T, Liu K.   +5 more
europepmc   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

Modification and validation of the InVEST erosion model for application at a national scale. [PDF]

PLoS One
Hooftman DAP, Pywell RF, Evans PM, Goodwin CED, Redhead JW, Ridding LE, Varma V, Bullock JM.   +7 more
europepmc   +1 more source

3D‐Printed Corneal Substitutes: Materials, Fabrication, and Preclinical Progress

Advanced Materials Technologies, EarlyView.
Successful clinical translation of 3D‐printed corneal substitutes relies on the interplay between the bioink properties, cellular component, and the fabrication process. These factors influence the critical properties of the construct, including optical transparency, mechanical stability, suture retention, that ultimately govern long‐term stromal ...
Shadi Moshayedi, Ashley Vazquez, Alexander J. Choi, Dimitrios Karamichos, Jayoung Kim   +4 more
wiley   +1 more source

In vivo assessment of the Optipen optical reflectometer for detecting enamel surface changes following an erosive challenge. [PDF]

Clin Oral Investig
Debortolli ALB, Ionta FQ, Xavier ALM, Ferrari CR, Carvalho TS, Lussi A, Buzalaf MAR, Rios D.   +7 more
europepmc   +1 more source

Nature‐Derived Chitosan Biopolymer: A Promising Candidate for Sustainable Electronics

Advanced Materials Technologies, EarlyView.
In the creation of environmentally friendly devices, nature‐derived chitosan biopolymer is a promising contender for sustainable electronic research. It can be utilized to create more ecologically friendly scalable gadgets and has a variety of uses in different active layers of electronics.
Joshua McDonald, Ali Nawaz, Amandeep Singh, Prashant Sonar   +3 more
wiley   +1 more source

Keratin-based protection of enamel against acid-erosion. [PDF]

Front Dent Med
Mistry S, Sukumaran P, Elsharkawy S.
europepmc   +1 more source

Assessing coastal vulnerability to erosion and storm surges: The case of Richards Bay, South Africa. [PDF]

Jamba
Alakram S, Hedding DW.
europepmc   +1 more source