Results 111 to 120 of about 860,678 (269)
Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView.Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello +7 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
PERENCANAAN PENJADWALAN REPARASI KAPAL FERRY DENGAN MENGGUNAKAN METODE FLASH
Wave, 2018 Sebagai negara kepulauan di Indonesia kapal ferry mempunyai peran sangat vital untuk melayani angkutan penumpang dan barang dengan jarak pendek. Pada operasinya armada kapal ferry ini memiliki frekuensi waktu kedatangan dan keberangkatan yang ketat ...
Wisnu Firstdhitama +2 more
doaj
Advanced Engineering Materials, EarlyView.This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan +4 more
wiley +1 more source
KARAKTERISTIK SEA KEEPING KAPAL ANGKUT IKAN 60 GT DI SEBARAN WILAYAH PERIKANAN PERAIRAN INDONESIA
Wave, 2018 Kementerian Kelautan dan Perikanan (KKP) telah menetapkan lokasi pembangunan Sentra Kelautan dan Perikanan Terpadu (SKPT) di pulau-pulau kecil dan kawasan perbatasan.
Waluyo Waluyo +2 more
doaj
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Edible electronics needs integrated logic circuits for computation and control. This work presents a potentially edible printed chitosan‐gated transistor with a design optimized for integration in circuits. Its implementation in integrated logic gates and circuits operating at low voltage (0.7 V) is demonstrated, as well as the compatibility with an ...
Giulia Coco +8 more
wiley +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
ANALISIS PENGARUH KONFIGURASI CATENARY SPREAD MOORING PADA OPERABILITAS INSTALASI PIPA BAWAH LAUT
Wave, 2019 Aktivitas instalasi pipa bawah laut memerlukan tingkat keandalan yang tinggi agar tidak mengalami kegagalan. Maka dari itu banyak faktor harus dipertimbangkan saat proses desain sebelum kegiatan instalasi.
Helmi Arif Asmajuna +2 more
doaj