Results 131 to 140 of about 5,638 (259)

Micropillar‐Engineered Hybrid Adhesive Patch for Surface‐Conformable and Directional Adhesion

Advanced Materials Technologies, EarlyView.
This work presents a surface‐conformable hybrid adhesive integrating height‐optimized hexagonal micropillars with open‐rectangular cuts. The micropillars enhance rough‐surface contact and microscale crack arrest, while the cuts guide and reverse interfacial cracks for strong and directional adhesion. The multiscale architecture achieves robust pull‐off
Seongjin Park, Dong Kwan Kang, Haejin Bae, Ho‐Sup Jung, Hoon Eui Jeong   +4 more
wiley   +1 more source

Direct Restorative Closure of Maxillary Midline Diastema Using a 3D-Printed Matrix: A Case Report. [PDF]

Case Rep Dent
Toida Y, Hoshika S, Tsuchiya K, Kawamura M, Kawamoto C, Tomokiyo A.   +5 more
europepmc   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Comparative evaluation of surface roughness in cobalt-chromium alloy castings fabricated by different manufacturing techniques and influence of positive pressure investment technique on its surface roughness - An in vitro study. [PDF]

J Indian Prosthodont Soc
Sharma A, Reddy KM, Nagi D, Gupta S, Vardhan JH, Sharma M.   +5 more
europepmc   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source

Evaluation of marginal and internal adaptation of implant-supported PEEK crowns fabricated by 3D printing, milling, and pressing: a micro-CT analysis. [PDF]

BMC Oral Health
Mahrous AI, El-Shazly M, Mansour M, Shabaan AA, Mokhtar M, Tawfik A, Radwan MM.   +6 more
europepmc   +1 more source

Additively Manufactured Porous Ceramics as Tunable Dielectrics for Passive Temperature Sensing

Advanced Materials Technologies, EarlyView.
Porous ceramic lattices, 3D‐printed from a multicomponent oxide ink, are integrated with LC resonators for passive wireless temperature sensing. By tuning porosity, the dielectric properties and RF response are engineered to produce distinct resonant frequency shifts with temperature. The results establish a structure‐driven approach to customizing the
Sogol Heidarishahrivar, Aminul Islam, Chang Woo Gal, Insup Kim, Yeong‐Jin Choi, Woo Soo Kim   +5 more
wiley   +1 more source

Integrated Optothermal Paperfluidic Platform for Single-Step, Model-Driven CRISPR-Cas12a Diagnostics of <i>Mycobacterium tuberculosis</i>. [PDF]

ACS Omega
Thepbut A, Rupprom T, Thant LT, Nyein HK, Compiro P, Kaewsapsak P, Hannanta-Anan P.   +6 more
europepmc   +1 more source

Recent Advances of Slip Sensors for Smart Robotics

Advanced Materials Technologies, EarlyView.
This review summarizes recent progress in robotic slip sensors across mechanical, electrical, thermal, optical, magnetic, and acoustic mechanisms, offering a comprehensive reference for the selection of slip sensors in robotic applications. In addition, current challenges and emerging trends are identified to advance the development of robust, adaptive,
Xingyu Zhang, Liao Wu, Shuai He, Zhao Sha, Yuwan Huang, Shuying Wu, Dewei Chu, Chun H. Wang, Shuhua Peng   +8 more
wiley   +1 more source

3D Printing in custom tray design for complete dentures in patients with flabby tissues. [PDF]

Front Dent Med
Garcia Zea E, Benitez Sellan PL.
europepmc   +1 more source