Results 261 to 270 of about 163,433 (313)

Prediction of wear outcomes and mechanical characterization of innovative SiO₂ incorporated aluminium matrix composites. [PDF]

Sci Rep
Bhowmik A, Kumar R, Sharma K, Chauhan MR, Bains PS, Singh K, Gill HS, Romanovski V, Ashok N.   +8 more
europepmc   +1 more source

Multi-criteria wear performance optimization of waste-reinforced hybrid aluminum alloys via RSM, Fuzzy AHP, and Fuzzy WASPAS. [PDF]

Sci Rep
Sivam SPSS, Kesavan S, Santhosh AJ.
europepmc   +1 more source

Investigation of the Microstructure, Mechanical, and Wear Characteristics of the Boronized Layer on IN718 Alloy Treated Under Aging Conditions. [PDF]

Materials (Basel)
Xu L, Quan J, Zhang X, Xiao R, Zong X, Chen S.   +5 more
europepmc   +1 more source

Reliability assessment of key equipment for coal gasification using artificial intelligence technology. [PDF]

PLoS One
Wu L, Zhang Z, Ding R, Zhang W, Liu M.
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Development of an equation for the wear of polymers

Wear, 1995
Abstract The aim of this research was to investigate and analyze the wear of polymers by use of an empirical wear equation. A dimensional analysis was carried out to develop an equation in which the volume of polymer material worn during sliding on a horizontal pin-on-disk machine was expressed in terms of the operating conditions, properties of the ...
N. Viswanath, D.G. Bellow
openaire   +2 more sources

Development of a six station knee wear simulator and preliminary wear results

Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine, 1997
In order to assess the wear performance of different designs of total knee replacements (TKR), a six station multi-axis knee simulator has been designed, built and commissioned. The most important features of a knee simulator are representative angles of flexion-extension synchronized with a dynamically applied load, and a ...
I C, Burgess, M, Kolar, J L, Cunningham, A, Unsworth   +3 more
openaire   +2 more sources

Wear Studies for Development of an Intervertebral Disc Prosthesis

Spine, 1992
Two long-term wear behavior studies used in part of the process of selecting the best materials for a new all-metal orthopaedic spinal implant are presented. The relative and absolute wear volume rates of candidate metals were investigated through simulation of two bearing regions of an intervertebral disc prosthesis.
W G, Hellier, T P, Hedman, J P, Kostuik
openaire   +2 more sources

Challenges in Android Wear Application Development

2015
The research focus of this paper was to highlight current issues in wearable application development in Android Wear platform. The findings of the experimental research were discovered during the software development of a smart watch application, where the requirements and design were limited with the documented best practices.
openaire   +3 more sources

Tooth Development and Wear in Myotis

Journal of Mammalogy, 1956
the end of the parturition period, it reveals the changes that occur in the deciduous dentition. The immature animals of the collection ranged in age from a few days to approximately 50 days (Stegeman, 1954). The deciduous teeth are shed during this period and the permanent dentition acquired. The number of specimens and the conditions under which they
openaire   +1 more source

Wear with low-lubricity fuels I. Development of a wear mapping technique

Wear, 1993
Abstract Use of low-lubricity fuels such as Jet A-1 is now relatively common in military ground equipment, while severe refinery processes such as hydrotreating are removing reactive components from commercially available diesel fuels. Under critical conditions, durability problems with fuel-sensitive equipment emerge with the use of Jet A-1 ...
openaire   +1 more source