Results 101 to 110 of about 111,103 (317)
Discussion on Main Influencing Factor of Wear Resistance of Pre-lubricating Roller Chain
Jixie chuandong, 2020 The lubrication state has a great influence on the wear resistance of the ordinary industrial roller chain. The main factors affecting the wear resistance of the ordinary pre-lubricating roller chain are summarized starting with the movement ...
Zhaohua Shang +4 more
doaj
Advances in Materials Science and Engineering, 2020 Mechanical parts have a problem of wear when used in extreme environments. Aluminum, most used in the industrial field, is a representative material of light weight, but its wear resistance is not good.
Jihye An +6 more
doaj +1 more source
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Metal ceramic wear mechanisms [PDF]
, 1990 Sliding wear of metal-on-ceramic, ceramic-on-metal, and ceramic-on-ceramic have been investigated using a tri-pin-on-disc machine. A technique has been developed for thin foil preparation for transmission electron microscopic examination perpendicular ...
Rainforth, William Mark
core
An Investigation of the Wear Resistance of Knitting Machinery Needle [PDF]
, 2013 Comparison tests of needles made in abroad and domestic on chemical composition, microstruture, mechanical property and so on, the main influence factors of the wear resistance were analysed.
Song, Zhenlun +4 more
core +1 more source
Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids
Advanced Functional Materials, EarlyView.This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow +9 more
wiley +1 more source
Enhancing the wear resistance of magnetron sputtered VN coating by Si addition [PDF]
, 2016 Although Si addition into transition metal nitrides has been long known to enhance hardness of coatings, relatively less evidence indicates that the hardness gain can be translated into a significant improvement of wear resistance as expected.
Ge, Fangfang +3 more
core
Material Characterization and Real-Time Wear Evaluation of Pistons and Cylinder Liners of the Tiger 131 Military Tank [PDF]
, 2013 Material characterisation and wear evaluation of the original and replacement pistons and cylinder-liners of Tiger 131 is reported. Original piston and cylinder-liner were operative in the Tigers’ engine during WWII.
Hadfield, Mark +3 more
core +1 more source
Advanced Functional Materials, EarlyView.Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein +4 more
wiley +1 more source