Results 91 to 100 of about 110,539 (317)

Discussion on Main Influencing Factor of Wear Resistance of Pre-lubricating Roller Chain

Jixie chuandong, 2020
The lubrication state has a great influence on the wear resistance of the ordinary industrial roller chain. The main factors affecting the wear resistance of the ordinary pre-lubricating roller chain are summarized starting with the movement ...
Zhaohua Shang, Wenjun Tao, Chengfeng Liu, Hongju Fu, Anlong Zhang   +4 more
doaj  

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Sliding wear of nitrided steels

, 1993
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The unlubricated sliding wear behaviour of gas nitrided, plasma nitrided, and ferritic nitrocarburized BS970,905M39 (EN41B) steels was investigated ...
Kato, Hirotaka, Kato, H
core  

Wear resistance of materials used for slurry transport

, 2015
More and more slurry transport systems are used in mining operations to efficiently and cost-effectively transport ores and tailings. The materials used for slurry transport are often subjected to severe wear attack.
Yick, Sing, Xie, Yongsong, Tufa, Kidus Yoseph, Jiang, Jiaren (Jimmy)   +3 more
core   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Metal ceramic wear mechanisms [PDF]

, 1990
Sliding wear of metal-on-ceramic, ceramic-on-metal, and ceramic-on-ceramic have been investigated using a tri-pin-on-disc machine. A technique has been developed for thin foil preparation for transmission electron microscopic examination perpendicular ...
Rainforth, William Mark
core  

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source

Hot‐Film and Calorimetric Methods With Transient Heating for Measurement of High Biofluid Flow Rate

Advanced Functional Materials, EarlyView.
Accurate measurement of biofluid flow rate is vital for clinical diagnostics. We propose a transient heating strategy using short thermal pulses and peak temperature tracking to enhance the flow sensitivity of the hot‐Film and calorimetric methods. Simulations show how optimal heating time maximizes sensitivity across flow rates.
Yuanting Wei, Shupeng Li, Kyung Rok Pyun, Tianyu Yang, Bosung Kim, Haotian Yang, John A. Rogers, Yonggang Huang, Haohui Zhang   +8 more
wiley   +1 more source

Wear Resistance of Sintered Composite Hardfacings under Different Abrasive Wear Conditions

Medžiagotyra, 2017
The article focuses on vacuum liquid phase sintered (PM) composite hardfacings and their behaviour under different abrasive wear conditions. Hardfacings studied contained 30 – 50 vol % fine, coarse or multimodal (fine and coarse) hardmetal reinforcement.
Taavi SIMSON, Priit KULU, Andrei SURŽENKOV, Riho TARBE, Dmitri GOLJANDIN, Marek TARRASTE, Mart VILJUS, Rainer TRAKSMAA   +7 more
doaj   +1 more source

Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer

Advanced Functional Materials, EarlyView.
Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero, Meghna Jha, Elsa Veronica Flores‐Vela, Joost Kimpel, Andreas Schaefer, Jiali Guo, Jesika Asatryan, Alberto Peinador Veiga, Shuichi Haraguchi, Per‐Anders Carlsson, Jaime Martín, Mariano Campoy‐Quiles, Christian Müller   +12 more
wiley   +1 more source