Results 21 to 30 of about 5,777 (224)
Influence of machining parameters on surface roughness in WEDM cutting [PDF]
Journal of Research and Innovation for Sustainable Society, 2020 Wire Electrical Discharge Machining is a cutting method used for obtaining parts with complex geometries or for cutting hard metals. This рарer ѕeekѕ to emрhаѕіze the іmрortаnce of thіѕ unconventіonаl technology аnd more ѕрecіfіcаlly the іmрortаnce of ...
Sergiu Lazăr
doaj +1 more source
Influence of pre‐strain and bake hardening on the static and fatigue strength of a DP600 steel sheet
Fatigue &Fracture of Engineering Materials &Structures, Volume 46, Issue 10, Page 3622-3639, October 2023., 2023 Abstract The influence of pre‐strain on the tensile and fatigue properties of a dual phase DP600 steel was studied. The material was pre‐strained by uni‐axial tension in rolling and transverse direction. Thereafter, specimens were cut from the deformed plates in parallel or orthogonal to pre‐strain direction.
Andrea Kusch +5 more
wiley +1 more source
Manufacturing Review, 2021 Wire electrical discharge machining (WEDM) is a popular non-conventional machining process used particularly for making extrusion dies, blanking punches, and tools especially requiring tight dimensional tolerances.
Nayak Ipsita, Rana Jaydev
doaj +1 more source
Bioinspired Golden Spiral Shapes on Crushing Protection Behaviors of Tubular Structures
Advanced Engineering Materials, Volume 25, Issue 17, September 2023., 2023 A tubular structure inspired by a golden spiral is investigated to understand the effects of spirals on impact energy absorption. The tube shows notable improvement over traditional structures, demonstrating the strength of curvature on energy absorption.
John Sherman +5 more
wiley +1 more source
Comparative Analysis of WEDM with Different wire Electrodes Applied to Cut Titanium Ti6Al4V
Journal of Machine Engineering, 2020 The machining of titanium alloys by traditional methods causes many disadvantages of both technical and economic nature. These materials are characterized by very low thermal conductivity and belong to hard to machine materials.
Dariusz Poroś +2 more
doaj +1 more source
Unexpected Event Prediction in Wire Electrical Discharge Machining Using Deep Learning Techniques [PDF]
, 2018 Theoretical models of manufacturing processes provide a valuable insight into physical phenomena but their application to practical industrial situations is sometimes difficult.
Arriandiaga, Ander +4 more
core +3 more sources
Research Papers Faculty of Materials Science and Technology Slovak University of Technology, 2016 Abstract This paper is focused on the effect of generator’s parameters on the stability of WEDM process that is expressed by the length of time of cutting until the wire electrode breaks. This paper provides an overview of the current research articles dealing with the causes of the wire electrode’s rupture and the options of control and
openaire +1 more source
Archives of Metallurgy and Materials, 2015 The influence of the parameters of wire electrical discharge machining (WEDM) on the surface layer of FeAl based sinters with and without Al2O3 nanoceramic addition has been studied in this paper.
Ziętala M., Durejko T., Łazińska M.
doaj +1 more source
A centrifugo-magnetically actuated gas micropump [PDF]
, 2006 This paper describes a novel gas micropump on a centrifugal microfluidic platform. The pump is integrated on a passive and microstructured polymer disk which is sealed with an elastomer lid featuring paramagnetic inlays.
Ducrée, Jens +3 more
core +1 more source
Sustainable machining: process energy optimisation of wire electrodischarge machining of Inconel and titanium superalloys [PDF]
, 2017 Process energy optimisation is vital in view of the environmental performance of electrodischarge machining (EDM). This research is focused on identifying the significant parameters that optimise the process energy consumption of wire EDM (WEDM) of ...
Antar, Mohammad +3 more
core +1 more source