Results 231 to 240 of about 1,076,501 (310)

An integrated cubic Pythagorean fuzzy MAIRCA model with novel variation coefficient similarity measure for food safety risk assessment. [PDF]

Sci Rep
Liu Z, Weng Z, Ksibi A, Singh NSS, Abbas M, Dhumras H, Hosseinzadeh M.   +6 more
europepmc   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Research on Covert Communication in Satellite-Ground-Integrated Sensor Networks Based on FH-DL-MPWFRFT. [PDF]

Sensors (Basel)
Ni L, Cai Y, Li X, Hu H, Chu Z, Qi Y.
europepmc   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Orthogonal Band Planning and Synergistic Interference Suppression for Full-Duplex Acoustic Telemetry in Coiled Tubing of Deep Horizontal Wells. [PDF]

Sensors (Basel)
Geng H, Xie Y, Wu J, Wang Z, Han H, Yang D.   +5 more
europepmc   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

First-in-human radiation dosimetry of the GRPR antagonist [⁶⁸Ga]Ga-NOTA-PEG₂-RM26 in patients with prostate and breast cancer. [PDF]

EJNMMI Res
Bjäreback A, Estenberg U, Tzortzakakis A, Axelsson R, Li C, Altena R, Tran TA, Hindorf C.   +7 more
europepmc   +1 more source

Biomass Native Structure Into Functional Carbon‐Based Catalysts for Fenton‐Like Reactions

Advanced Functional Materials, EarlyView.
This study indicates that eight biomasses with 2D flaky and 1D acicular structures influence surface O types, morphology, defects, N doping, sp2 C, and Co nanoparticles loading in three series of carbon, N‐doped carbon, and cobalt/graphitic carbon. This work identifies how these structural factors impact catalytic pathways, enhancing selective electron
Wenjie Tian, Jingkai Lin, Zhihao Tian, Selusiwe Ncube, Huayang Zhang, Emiliano Cortés, Hongqi Sun, Shaobin Wang   +7 more
wiley   +1 more source

Economic Policy Uncertainty and Health: Empirical Evidence from the MIDAS Model. [PDF]

Healthcare (Basel)
Lin M, Fei J.
europepmc   +1 more source