Results 131 to 140 of about 350,354 (303)

Software‐Defined Terahertz Beam Manipulation via Active Light‐Controlled Frequency Coding Information Metasurface

Advanced Physics Research, EarlyView.
This paper proposes an integrated active light‐controlled frequency coding metasurface and a software‐defined array control system. Utilizing spatially encoded structured light and a “Decision‐Optimization‐Execution” intelligent closed‐loop architecture, the system overcomes traditional electrical control interference, achieves real‐time dynamic ...
Chao Zhao, Min Jia, Rong Lu, Yifan Ma, Gaole Fan, Qing Guo, Yanhong Tian, Siyuan Yu   +7 more
wiley   +1 more source

Laser Welding

Welding International, 2003
openaire   +2 more sources

Exposure to Occupational Inhalants and the Risk of Developing Rheumatoid Arthritis: A Systematic Review and Meta‐Analysis

Arthritis &Rheumatology, EarlyView.
Objective Rheumatoid arthritis (RA) is a chronic autoimmune disease characterized by joint pain, swelling, and stiffness. Although smoking is a well‐established risk factor for RA, the role of occupational inhalants in RA development is less well recognized.
Qianwen Liu, Xin Song, Emily Mauro, Yuan Jiang, Klementy Shchetynsky, Lars Klareskog, Lars Alfredsson, Xia Jiang   +7 more
wiley   +1 more source

On Slow Money

Maine Policy Review, 2011
Linzee Weld
doaj  

Welding Seam Recognition and Trajectory Planning Based on Deep Learning in Electron Beam Welding. [PDF]

Sensors (Basel)
Yang H, Zuo C, Xu H, Xu X.
europepmc   +1 more source

Scaling of Planar Sodium‐Nickel Chloride Battery Cells to 90 cm2 Active Area

Batteries &Supercaps, Volume 8, Issue 3, March 2025.
Large planar Na β′′ alumina electrolytes are prepared by tape‐casting and die‐pressing. These ceramic electrolytes are used to prepare planar sodium‐nickel chloride cells with 90 cm2 active area, providing a high capacity of 7 Ah. Successful cell cycling is demonstrated at 300 °C at rates up to C/4 (20 mA cm−2) for a cumulative capacity of 3.6 Ah cm−2.
T. Lan, E. Svaluto‐Ferro, N. Kovalska, G. Graeber, F. Vagliani, D. Basso, A. Turconi, M. Makowska, G. Blugan, C. Battaglia, M. V. F. Heinz   +10 more
wiley   +1 more source

More Than 10 Years on: Does a State‐of‐the‐Art Review and Synthesis Offer New Frameworks to Guide Future Design for Remanufacturing Research?

Business Strategy and the Environment, EarlyView.
ABSTRACT There is strong evidence that design for remanufacturing (DfRem) can reduce initial‐design carbon emissions by up to 30%, and that product design can critically affect remanufacturing feasibility, yet academic adoption of DfRem remains limited.
Okechukwu Okorie, Yogendra Singh, Jennifer Russell, Chris Turner, Kingsley Oturu   +4 more
wiley   +1 more source

Structural Aspects of Lithium‐Ion Conduction in the Phosphidotitanate Li8TiP4 and Its Comparison With Li7+5xTa1−xP4 and Li8−xTi1−xTaxP4

Chemistry – A European Journal, EarlyView.
ABSTRACT The chemical system Li/Ti/P has previously been subject to intensive investigation. However, reliable structural data for the reported phases have remained elusive. Motivated by the growing interest in phosphorus‐based lithium‐ion conductors, we have reinvestigated the synthesis, crystal structure, and physical properties of Li8TiP4.
David Müller, Tobias Kutsch, Sabine Zeitz, Viktor Hlukhyy, Gabriele Raudaschl‐Sieber, Wilhelm Klein, Thomas F. Fässler   +6 more
wiley   +1 more source

Sensitivity analysis and stochastic optimization of levelized cost of hydrogen production through methane pyrolysis

The Canadian Journal of Chemical Engineering, EarlyView.
Abstract Hydrogen plays a crucial role across multiple industrial sectors and is increasingly recognized as a clean energy carrier with significant potential in decarbonization efforts. Methane pyrolysis (MP), particularly using molten metal catalysts, offers a promising pathway for hydrogen production with low CO2 emissions.
Adrian Paredes Bozzo, Zukui Li
wiley   +1 more source

WELDABILITY, WELDING METALLURGY, WELDING CHEMISTRY

Kapal, 2012
Sambungan las merupakan bagian penting dari stuktur/bangunan yang dilas, dan kunci dari logam induk yang baik adalah kemampuan las (weld ability). Kemampuan las yang baik dan kemudahan dalam fabrikasi dari suatu logam merupakan pertimbangan dalam memilih suatu logam untuk konstruksi.
openaire   +1 more source