Results 171 to 180 of about 2,407 (262)

Influence of Wire Arc Additive Manufacturing Parameters on the Morphology, Microstructure, and Hardness of DSS2209 Single-Bead Deposited Layers. [PDF]

Materials (Basel)
Sun J, Liu L, Zhang L, Liu F, Wang D, Yang Y.   +5 more
europepmc   +1 more source

Insights Into Paint‐Bake Toughening of Resistance Spot Welds of a 2.0 GPa Warm‐Stamped Medium‐Mn Steel

steel research international, EarlyView.
Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan, Savyasachi Nellikode, YeoJin Jang, Sumin Lee, Dileep Chandran Ramachandran, Sung‐bo Heo, Jinyoung Lee, Young‐Kook Lee, Yeong‐Do Park   +8 more
wiley   +1 more source

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Residual Stress Relief in High-Strength Steel Welded Joints: Creep-Based Material Modeling and Post-Weld Treatment Simulation. [PDF]

Materials (Basel)
Ding P, Zheng S, Zhou J, Tang X, Shan H, Lu C, Zheng W, Gong X, Niu J, Xu L.   +9 more
europepmc   +1 more source

Performance analysis of strengthening reinforced concrete beams under pure torsion using galvanized steel sheets: Experimental and numerical investigation

Structural Concrete, EarlyView.
Abstract Reinforced concrete (RC) beams can be subjected to torsion, and failure due to torsion is brittle and poses a significant risk to occupants. Moreover, strengthening of existing RC beams in torsion may be required due to the upgrade of the structures or as part of structural rehabilitation.
Ahmed Hamoda, Mizan Ahmed, Ahmad G. Saad, Aref A. Abadel, Saad A. Yehia   +4 more
wiley   +1 more source

Properties of Laser-Welded Zr-Al-Co-Nb Bulk Metallic Glass. [PDF]

Materials (Basel)
Wang HS, Hsieh CC, Chen HG, Wu SC, Jang JS, Lee KJ.   +5 more
europepmc   +1 more source

Experimental and theoretical investigation of longitudinal tunnel lining joints with confining reinforcement

Structural Concrete, EarlyView.
Abstract Precast reinforced concrete segmental linings are frequently used in modern tunneling. In these linings, the longitudinal joints typically have a reduced contact cross‐section and thus often govern the design, particularly in tunnels under high hydrostatic pressure or crossing squeezing or swelling ground with correspondingly high ...
Fabian Morger, Albin Kenel, Walter Kaufmann   +2 more
wiley   +1 more source

Emerging Trends in Ultrasonic and Friction Stir Spot Welding of Polymers and Metal-Polymer Hybrids: A Review of Process Mechanics, Microstructure, and Joint Performance. [PDF]

Materials (Basel)
Kumari K, Pradhan S, Samantra C, Priyadarshini M, Barua A, Dhupal D.   +5 more
europepmc   +1 more source

Moment‐curvature behavior of continuous reinforced concrete slab strips—Experimental determination and modeling

Structural Concrete, EarlyView.
Abstract With the market introduction of new reinforcing materials, such as corrosion‐resistant steel, the effect of their stress–strain relationship on the ductility of reinforced concrete structures needs to be evaluated. Their moment‐curvature behavior significantly influences bending moment redistributions, rotation capacity, and deformation at ...
Nathalie Reckinger, Karel Thoma, Walter Kaufmann   +2 more
wiley   +1 more source

Tab-to-Busbar Interconnections in EV Battery Packs: An Introductory Review of Typical Welding Methods. [PDF]

Micromachines (Basel)
Choi S, Lim S, Shan A, Lee J, Yun TG, Hwang B.   +5 more
europepmc   +1 more source