Results 161 to 170 of about 12,448 (306)

Thermomechanical Validation of an Additively Manufactured Test Chamber for Sustainable Aviation Fuel Atomization in Jet‐In‐Crossflow Conditions

Macromolecular Symposia, EarlyView.
ABSTRACT This study aims to validate the structural and thermomechanical reliability of an additively manufactured test chamber specifically designed for the experimental investigation of sustainable aviation fuel (SAF) atomization under jet‐in‐crossflow (JICF) conditions representative of gas turbine afterburners. The proposed test chamber is designed
Valerio Acanfora, Giancarlo Sorrentino, Giovanni Battista Ariemma, Raffaele Ragucci, Aniello Riccio   +4 more
wiley   +1 more source

Study on the effect of high energy ultrasonic wave on MIG welding deformation and welding joint performance of LC52 aluminum alloy plate. [PDF]

Sci Rep
Jin C, Xu C, Li P, Yin P, Gao Y, Wang Y.
europepmc   +1 more source

Prediction and Welding sequence of Minimum Welding Deformation in Large Steel Block Welding [PDF]

Journal of Welding and Joining, 2017
Jeong-ung Park, Gyubaek An, Seung-hyun Yang   +2 more
openaire   +1 more source

A Comparison of Classical Constitutive Models for High‐Entropy Alloy Behavior: Effects of Medium Strain Rates and Temperature on Plastic Flow

Materials Genome Engineering Advances, EarlyView.
Four constitutive models are evaluated for FeCoNiCr and Al0.6FeCoNiCr HEAs under wide temperature and strain‐rate conditions. The predictive capabilities and limitations of each model are then critically assessed, with particular emphasis on strain rate sensitivity, temperature dependence, and physically unrealistic responses at extreme loading ...
Yooseob Song, Daniel Garcia‐Gonzalez, Tomasz Jankowiak, Alexis Rusinek   +3 more
wiley   +1 more source

Prediction of Welding Deformation Using the Thermal Elastic-Plastic Finite Element Method by Considering Welding Interpass Temperature. [PDF]

Materials (Basel)
Han YH, Lim HB, Shin TS, Yang HI.
europepmc   +1 more source

Simulating Deformation of Welding Joints

, 2019
В работе было выполнено компьютерное моделирование процессов изготовления сварных конструкций из тонколистовых заготовок. Результаты моделирования были использованы для уменьшения остаточных напряжений и деформаций сварных соединений.
Пантелеенко, Ф. И., Shumav, A., Panteleenko, F., Шумов, О. В.   +3 more
core  

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, EarlyView.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Effect of Welding Gap of Thin Plate Butt Welds on Inherent Strain and Welding Deformation of a Large Complex Box Structure. [PDF]

Materials (Basel)
Zhang L, Peng G, Yang F, Meng Z, Yuan X, Fan Y, Li W, Zhang L.   +7 more
europepmc   +1 more source

Welding Deformation Produced by Two-pass Weld

Preprints of the National Meeting of JWS, 2007
Andou, Akira, Terasaki, Toshio, Fujikawa, Takaharu   +2 more
openaire   +1 more source

Effect of Nominal Laminate Thickness on Consolidation Quality and Tensile Properties of Compression‐Molded Polyetherketoneketone/Carbon Fiber Composites

Polymer Composites, EarlyView.
Effect of Mold Cavity Thickness on Consolidation Quality and Tensile Strength of CF/PEKK Composites. ABSTRACT Carbon‐fiber‐reinforced thermoplastic composites have attracted growing attention as high‐performance structural materials due to their superior toughness, shorter processing cycles, and recyclability.
Hyunseok Choi, Chan Joo Lee, Chang‐Soo Kang, Dongearn Kim   +3 more
wiley   +1 more source