Results 191 to 200 of about 4,090,931 (280)

Mechanical and Impact Response of Adhesively Bonded ASA/PA12 Sandwich Structures Produced by Fused Filament Fabrication

Polymer Engineering &Science, EarlyView.
Adhesively bonded ASA/PA12 FFF sandwich structures reveal that interfacial compliance governs mechanical performance. Cyanoacrylate enhances strength but induces brittle failure, while polyurethane improves ductility and impact resistance, demonstrating that adhesive properties and stacking sequence are critical design parameters for optimizing multi ...
Berkay Ergene, Bayram Yildiz, Tolgahan Ermergen, Çağın Bolat   +3 more
wiley   +1 more source

Simulation of the Rotational Molding Process of Polyethylene Using the Smoothed Particle Hydrodynamics Method

Polymer Engineering &Science, EarlyView.
Numerical simulation of polyethylene rotational molding using the Smoothed Particle Hydrodynamics (SPH) method. ABSTRACT This work presents the development of a numerical model based on the smoothed particle hydrodynamics (SPH) method to simulate the rotational molding process of powder thermoplastic polymers, used in the manufacture of liners for high‐
Ali Nourreddine, Albert Lucas, Séverine Boucaud‐Gauchet, Abbas Tcharkhtchi, Sofiane Khelladi   +4 more
wiley   +1 more source

Microstructural Control, Property Trade-Offs and Emerging Design Strategies in Conventional Aluminum Alloys. [PDF]

Materials (Basel)
Zhang S, Li B, Wang Z, Han J, Shi Q.
europepmc   +1 more source

The iPP Printing Paradox: Interlayer Adhesion Through Crystallization

Polymer Engineering &Science, EarlyView.
In fused filament fabrication of isotactic polypropylene, high molecular weight and a high print speed increase the shear during deposition. This shear promotes the formation of the ductile β‐phase at the interphase, which improves interlayer adhesion, as shown by an eightfold increase in fracture energy measured via a T‐peel test on two printed ...
Paul M. H. van Heugten, Michelle M. A. Spanjaards, Martin Rosenthal, Patrick D. Anderson, Stan F. S. P. Looijmans, Lambèrt C. A. van Breemen   +5 more
wiley   +1 more source

Welding Techniques for Magnesium Alloy Joints: A Comprehensive Review. [PDF]

Materials (Basel)
Poliak M, Czyzewski P, Kubiak P, Frej D, Rylski A, Wozniak M, Siczek K.   +6 more
europepmc   +1 more source

Characteristics, properties and limitations of per‐ or polyfluoroalkyl substances (PFASs) and fluoropolymers

Polymer International, EarlyView.
An overview and categorization of man‐made per‐ or polyfluoroalkyl substances (PFASs) including low‐molar‐mass and high‐molar‐mass fluorochemicals, and their international regulations is presented. Though certain PFASs are toxic, bioaccumulative and cross the human cellular membranes, others, such as fluoropolymers, are safe, reliable and involved in ...
Bruno Améduri
wiley   +1 more source

Bimetallic Steels: A Structured Review of Fabrication Routes, Material Properties, and Component Performance. [PDF]

Materials (Basel)
Ding Z, Xue X, Wang F, Wang N, Li S, Hua J.   +5 more
europepmc   +1 more source

Influence of porosity and architecture on the mechanical and acoustic properties of FFF‐printed PLA structures

Polymer International, EarlyView.
The influence of porosity and infill pattern (architecture) on the mechanical and acoustic properties of FFF‐printed PLA is investigated. Ultrasonic analysis highlights the dominant role of interlayer porosity, revealing anisotropic behavior and a transition in elastic properties with increasing porosity.
Makki Ajmi, Simon Bernard, Slim Souissi, Ahmed Elloumi, Pierre Maréchal   +4 more
wiley   +1 more source

Progress and Challenges in Joining for Precision Endoscope Fabrication. [PDF]

Sensors (Basel)
Xu P, Zheng X, Li L, Wang Z.
europepmc   +1 more source