Results 21 to 30 of about 814,315 (295)
Simulation of the deflected cutting tool trajectory in complex surface milling [PDF]
, 2011 Since industry is rapidly developing, either locally or globally, manufacturers witness harder challenges due to the growing competitivity. This urges them to better consider the four factors linked to production and output: quality, quantity, cost and
Baili, Maher +9 more
core +1 more source
Annals of "Dunarea de Jos" University of Galati, Fascicle XII, Welding Equipment and Technology, 2020 The research activities are oriented towards elaborating and characterizing nano-sized powders by powder metallurgy technologies based on wet milling in a planetary mill.
I. Stefan, G. C. Benga, A. Olei
doaj +1 more source
Foods, 2023 Due to the large consumption and discharge of water in wet milling, dry-milling is an alternative to produce waxy rice flour. The physical properties and sensory characteristics for preparing waxy rice balls in dry-milled waxy rice flour were compared in
Sicong Fang +4 more
doaj +1 more source
Experimental Analysis and Geometrical Modeling of Cutting Conditions Effect in 5 Axis Milling with Ti6Al4V Alloy [PDF]
, 2012 The 5 axis continuous milling is an advanced technique for free-form surfaces manufacturing. In finishing, this technique uses ball-end or hemispherical milling cutter.
PRAT, David +3 more
core +1 more source
Effects of particle shaping on the performance of phosphorus building gypsum
Case Studies in Construction Materials, 2023 Phosphogypsum (PG) is an industrial by-product from the wet preparation of phosphoric acid. Phosphorus building gypsum (PBG) can be obtained from PG after high-thermal dehydration. Improving the properties of PBG is of great significance to extending its
Yi Zhang +5 more
doaj +1 more source
Comparison of Fabrication Technique and Carrier Oil to Curcumin Nanoemulsion Properties [PDF]
Journal of Pure and Applied Chemistry Research, 2023 Turmeric (Curcuma longa L.) is included in the rhizome plant containing curcumin which has various therapeutic properties. However, curcumin has poor bioavailability. The manufacture of nanoemulsion is expected to increase curcumin bioavailability.
Zubaidah Ningsih +4 more
doaj
Induction-heated ball-milling: a promising asset for mechanochemical reactions [PDF]
, 2023 While ball-milling is becoming one of the common tools used by synthetic chemists, an increasing number of studies highlight that it is possible to further expand the nature and number of products which can be synthesized, by heating the reaction media ...
Nicolas, Fabrègue +5 more
core +2 more sources
Property Modification of Ball-milled Slurries using Wet-jet Milling
Journal of the Japan Society of Powder and Powder Metallurgy, 2008 Wet-jet milling process was employed to modify the properties of Al2O3 slurry after ball milling. Particle size distribution of slurry wet-jet milled after ball milling corresponded to that of ball-milled slurry. However, the viscosity of ball-milled slurry increased rapidly with time, whereas the viscosity of the slurry wet-jet milled after ball ...
Hotta, Yuji +5 more
openaire +2 more sources
A new model-based approach for power plant Tube-ball mill condition monitoring and fault detection [PDF]
, 2014 With the fast growth in intermittent renewable power generation, unprecedented demands for power plant operation flexibility have posed new challenges to the ageing conventional power plants in the UK. Adding biomass to coal for co-fired power generation
Wei, Jianlin +3 more
core +1 more source
Correlation between machining direction, cutter geometry and step-over distance in 3-axis milling: Application to milling by zones. [PDF]
, 2012 Computer-Aided Manufacturing (CAM) occupies an increasingly important role in engineering with all it has to offer in terms of new possibilities and improving designer/manufacturer productivity. The present study addresses machining of free-form surfaces
Senatore, Johanna +3 more
core +1 more source