Results 71 to 80 of about 5,043 (195)
Dispersion of Carbon Nanotubes in Cu-Cr Matrix Nano-composite by Wet Milling [PDF]
, 2015 The preparation of Cu-2wt%Cr-5wt%CNT nano-composite powder by wet ball milling was investigated. The lattice parameter and mean crystallite size were calculated by X-ray diffraction technique.
Masroor, M., Ataie, A., Sheibani, S.
core +1 more source
EnergiesBall mills are widely used for size reduction in mineral processing, but effective scaling from laboratory to industrial scale remains challenging. This study introduces a novel scaling constant approach to replicate energy transfer to ore during milling
Błażej Doroszuk +3 more
doaj +1 more source
Investigation of MgTiO3 as an anode material for rechargeable Li-ion batteries
Ceylon Journal of Science, 2016 Magnesium Titanate (MgTiO3) is a common and commercially available dielectric material used in electronics applications. The potential of using MgTiO3 as an anode material in rechargeable Li-ion batteries has been investigated under this study.
Thushan Pathirana +2 more
doaj +1 more source
Effects of Typical Solvents on the Structural Integrity and Properties of Activated Kaolinite by Wet Ball Milling. [PDF]
Nanomaterials (Basel), 2022 Luo S +8 more
europepmc +1 more source
Characterization of Lignin Isolated from Wheat Leaf Based on LiCl/DMSO Dissolution and Regeneration
BioResources, 2016 The isolation of lignin is of great importance to understand its structural characteristics. A lithium chloride/dimethyl sulfoxide (LiCl/DMSO) solvent system has been developed for the dissolution of lignocellulose and for the isolation of lignin for ...
Tingyue Cao +4 more
doaj +1 more source
A technical and economic comparison of Wet Milling versus Dry Milling (Vertical Roller Mill) [PDF]
, 2020 A dissertation submitted to the Faculty of Engineering and the Built Environment University of the Witwatersrand, in fulfillment of the requirements for the Degree of Master of Science in Engineering, 2020Stringent SO2 emission regulations have placed ...
Swart, C
core
AIP AdvancesState-of-the-art soft magnetic (SM) alloy systems such as electrical steels and permalloys exhibit large eddy current losses at high-frequency (kHz range and above), limiting their application in fast switching devices. Eddy current losses can be reduced
Ward Burgess +2 more
doaj +1 more source
Journal of Bioresources and BioproductsWater-soluble lignin-carbohydrate complex (LCC) rich in polysaccharides exhibits benign in vitro antioxidant activities and distinguishes high biocompatibility from lignin-rich LCC and lignin.
Di Xie +5 more
doaj +1 more source
Ultrafine Sm-Fe-N Particles Prepared by Planetary Ball Milling
EPJ Web of Conferences, 2013 Ultrafine magnetically hard particles are needed for the bottomup fabrication of anisotropic exchangedcoupled permanent magnets. In this study we have chosen Sm2Fe17Nx because of its high anisotropy field and large saturation magnetization.
Neil D., Hadjipanayis G., Gabay A.
doaj +1 more source
Preparation of Fine AlN Powders by Wet Ball-Milling and Their Characterization
Journal of the Ceramic Society of Japan, 1997 Aluminum nitride (AlN) raw powder prepared by direct nitridation of metallic aluminum powder was ground by wet ball-milling in order to obtain submicron fine powder for low-temperature sintering. The effects on the properties of the milled powders of milling conditions such as ball size, ball material, chemical species of the grinding fluid and water ...
NAGAI, Yuji, LAI, Gao-Chao
openaire +2 more sources