Results 41 to 50 of about 620,870 (296)
Influence of curing on pore properties and strength of alkali activated mortars [PDF]
, 2018 The paper investigates the effect of wet/dry, wet and dry curing on the pore properties and strength of an alkali activated cementitious (AACM) mortar.
Aligizaki +29 more
core +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Viscose Rayon: An Absorbing Problem. An Investigation into the Impact Conservation Wet Cleaning Treatments have on Historic Woven Viscose Rayon Fabrics; with a Supplementary Analysis of Current Techniques for Identifying Man-Made Fibres [PDF]
, 2013 Viscose rayon has been in production for over a century, however, minimal literature is available on its conservation. Pre-1940s viscose rayon has poorer wet strength than later versions.
Gamper, Charlotte +2 more
core
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Mechanisms for slow strengthening in granular materials [PDF]
, 1999 Several mechanisms cause a granular material to strengthen over time at low applied stress. The strength is determined from the maximum frictional force F_max experienced by a shearing plate in contact with wet or dry granular material after the layer ...
A. Ruina +33 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
The Retention of Wet Strength Resins as Determined by the Kjeldahl Method [PDF]
, 1952 True wet strength is not a gauge of water proofness of paper, but is a measure of the residual strength of the paper gauged by the mullen, tear, burst, and fold, after the paper has been completely soaked in water and the resistance to water penetration ...
Redmond, Walter J.
core +1 more source
The Role of Contact Angle Hysteresis for Fluid Transport in Wet Granular Matter [PDF]
, 2015 The stability of sand castles is determined by the structure of wet granulates. Experimental data about the size distribution of fluid pockets are ambiguous about their origin.
Brinkmann, Martin +5 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Case Studies in Construction Materials, 2020 This paper investigates the compressive strength loss of wollastonite modified magnesium ammonium phosphate cement (MAPC) and magnesium potassium phosphate cement (MKPC) paste after exposure to NaCl freeze-thaw cycles, alternation of dry-wet (water ...
Linchun Zhang +6 more
doaj +1 more source