Results 51 to 60 of about 2,167,372 (274)

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Understanding Polyamidoamine Epichlorohydrin (PAAE) Retention in Paper

BioResources
Polyamidoamine epichlorohydrin (PAAE) is a permanent wet strength resin used in papermaking. When applied to paperboard, some amount of resin is retained in the sheet, and some is lost to the white water.
Yao Ntifafa, Yun Ji, Peter W. Hart
doaj   +2 more sources

Mechanism of Strength Expression by Wet Strength Agents.

JAPAN TAPPI JOURNAL, 1998
Some applications such as tissue papers or filter papers require strength at wet even though paper orginally has weakness to water. For these applications, wet strength agents that meet such requirement are added to papers at the stage of pulp slurry.Namely, we have polyamide resin or melamine resin for the additives that give paper strength at wet ...
openaire   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Experimental Research on Foamed Mixture Lightweight Soil Mixed with Fly-Ash and Quicklime as Backfill Material behind Abutments of Expressway Bridge

Advances in Materials Science and Engineering, 2017
To promote the utilization of fly-ash, based on the orthogonal experiment method, wet density and unconfined compressive strength of Foamed Mixture Lightweight Soil mixed with fly-ash and quicklime (FMLSF) are studied.
Xin Liu, Ke Sheng, Zhi-long Li, Liang-qin Gan, Hao Shan, Bao-ning Hong   +5 more
doaj   +1 more source

Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy

Advanced Engineering Materials, EarlyView.
Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang, Jianxiang Zhao, Zhaoqi Chen, Hao Gong, Yinsen Yan, Junlei Tao, Yong Yang   +6 more
wiley   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Polyamidoamine Epichlorohydrin (PAAE) Wet-strength Agent: Generations, Application, Performance, and Recyclability in Paperboard and Linerboard

BioResources
Polyamidoamine epichlorohydrin (PAAE) is the preeminent permanent wet strength additive used in papermaking. Wet strength additives are used to improve paper resistance to a rupture force in wet environments.
Yao Ntifafa, Yun Ji, Peter W. Hart
doaj   +2 more sources