Results 141 to 150 of about 426,887 (303)
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
ABUAD Journal of Engineering Research and DevelopmentRenewable energy plays a crucial role in sustainable development by enhancing human development and economic productivity. Analyzing the pipeline of installed wind farms across Africa reveals that the continent has substantial wind resources, with the ...
Imo Edwin Nkan +2 more
doaj +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Electron Velocity Moments in the Solar Wind. I. Calibration of the Wind 3DP EESA Low Detector
The Astrophysical Journal Supplement SeriesCalibrated measurements of electron velocity distribution functions (VDFs) are necessary to characterize fluid and kinetic processes in weakly collisional and nearly collisionless plasmas such as the solar wind.
Lynn B. Wilson III +6 more
doaj +1 more source
Journal of the Japan Society of Naval Architects and Ocean Engineers, 2019 Kenichi Kume +3 more
openaire +2 more sources
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Wind sensitivity studies of a non-return wind tunnel, with a 216- by 432-mm (8.5- by 17.0-inch) test section, phase 1 [PDF]
The study to develop inlet and exit treatments which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel is reported.
Eckert, W. T. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Wind Velocity Profile Above Progressive Water Waves
Coastal Engineering 1968, 1968 An investigation of the air velocity profile above progressive, mechanically-generated waves was made m the wind and wave facility at Stanford University. The influence of propagating waves on the mean velocity profile was sought especially. Both the instantaneous and mean velocity profiles were obtained with the use of high response total head and ...
openaire +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat +7 more
wiley +1 more source