Results 121 to 130 of about 426,887 (303)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Case Studies in Thermal EngineeringA range of fire experiments were conducted to explore fire characteristics and smoke dynamics in a 1/6-scale stairwell adjacent to a room at different external wind velocities.
Junjiang He +3 more
doaj +1 more source
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Effects of windblown dust on photovoltaic surface s on Mars [PDF]
Photovoltaic (PV) coverslip material was subjected to Maritan dust storm conditions using basaltic dust flowing through the Martian Surface Wind Tunnel at NASA-Ames.
Gaier, James R. +2 more
core +1 more source
Holographic Schwinger effect with a moving D3-brane
, 2017 We study the Schwinger effect with a moving D3-brane in a $\mathcal{N}$=4 SYM plasma with the aid of AdS/CFT correspondence. We discuss the test particle pair moving transverse and parallel to the plasma wind respectively. It is found that for both cases
Chen, Gang, Hou, De-fu, Zhang, Zi-qiang
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Interstellar helium in interplanetary space [PDF]
The velocity distribution function of He(+) in the solar wind at 1 AU is calculated with the assumption that the source is photoionization of a cold (T = 100 K), neutral interstellar wind.
Feldman, W. C., Lange, J. J., Scherb, F.
core +2 more sources
Solar-wind predictions for the Parker Solar Probe orbit
, 2017 The scope of this study is to model the solar-wind environment for the Parker Solar Probe's unprecedented distances down to 9.86 Rs in its mission phase during 2018-2025.
Bothmer, V., Venzmer, M. S.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source